Hi there,
I was going through Nordic Semiconductor's Introduction to Bluetooth Direction Finding video. In one slide of that, host talks about area of coverage of Antenna...
I am having a miserable time with Device Tree partitioning, when it comes to FOTA. Attached are my overlay files That's boards/nrf...overlay and sysbuild/mcuboot.overlay....
nRF5340 DK PCA10095 revision 2.0.0 Probe serial 1050093769. The onboard debugger fails to connect to the nRF5340. It successfully programs external targets through P20. The...
Hi Nordic team,
I'm investigating a systematic positive measurement error of approximately +8% when using the SAADC on an nRF9151 with its internal 0.6 V reference.
After...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
Hey.
I have a GPS chip which uses 57600 baud for its rx pin, and 115200 baud for its TX pin.
I need to switch between the two baud rates, and also some times connect to...
I'm using nRF51822_xxAA , with SDK12.3.0 and Softdevice S130 v2.0.1 on Keil V5.29.0.0. And as a central I use Redmi 7A phone with Android V10. I want to sample ADC @ 200Hz...
Hi,all:
There is a question when I run usb_msc example on nrf52840DK(sdk17.0.2),I do as following steps,
Then,after I press button 1 for serial times,I found there are...
I want to get started with nRF52832 in Arduino. I have a Ebyte development board with E73 module containing the NRF chip.
The hardware is quite similar to Adafruit NRF52...
Hi,
Hope you are doing well!
I am trying to do Buttonless DFU on our own Android APP. I have finished programming on nrf end and succeed doing DFU on 'nrf connect...
Hello, I have done customized board using nRF52832 and when I try to flash code using nRF52 DK(Jtag) it is showing following error. could not fetch memory size of target devkit...
Hey all - I'm new and trying to connect Thingy91 to nRF Connect V3.6.1 for the first time. When I open the Programmer app I only see "No devices available" in the drop down...
Hi,
I'm trying to follow the NCS tutorial in: https://devzone.nordicsemi.com/nordic/nrf-connect-sdk-guides/b/getting-started/posts/nrf-connect-sdk-tutorial---part-1-ncs...
Hi,
we are developing a custom BLE communication. For this we are using:
- nRF5_SDK_17.0.2_d674dde - s332 - based on BLE NUS UART example
Everything works fine, until...
I'm trying to open a NCS project in SES but I'm getting error 1 from create_nordic_project.py. NCS 1.5.0 installed with toolchain manager on macOS 11.2.2
The error in SES...
Hi,
I am following a client case that they have issue on accessing SD card via SPI port.
I used the sample project fat_fs on nrf9160_pca10090 DK and used SPI_3 to access...
nRF9160 DK schematic sheet 2 missing pin names for WP and HOLD of nRF91_EXT_MEM in the On-board interface (far right page 2)
could someone post what nRF9160 pins are used...
Hi,
I have written one application with logging disabled to save power.
However, when I tried to debug the code with Ozone, during startup, it raises BusFault exception...
Hi,
I am currently working on generating a dfu over serial uart by testing with the ble_app_blinky example given in the SDK 15.2.0. Currently the ble_app_blinky hex file...
Hi ! Using nRF52840 whith SD140 as central and 6 link count I research :
changing the NRF_SDH_BLE_GAP_EVENT_LENGTH from 6 to 2 does not change "Window size" on CONNECT_REQ...