While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Hi Nordic team,
I am working on a custom board based on the nRF54L15 using nRF Connect SDK v3.1.0.
On our hardware, the nRF54L15 has a 32 MHz crystal connected to XC1...
Hello,
I am using the nRF9151 DK with the Serial LTE Modem (SLM) application.
I put the device into sleep mode using:
AT#XSLEEP=2
This successfully disables the UART...
Hello Nordic team,
We are reviewing our nRF54LM20-CAAA (CSP61) hardware design and would appreciate your clarification on several power and RF related points.
DECRF...
Hi,
I have a question regarding the SAADC timing parameters.
I could not find an official specification for the SAADC power-up time (t_PWRUP). While measuring it on my...
Hi all — I'm developing a custom nRF5340 development board (Raytac MDBT53-1M) and would value the community's honest read on whether it's worth producing.
The goal is...
nRF54L replaces the RTCs from nRF52 with the GRTC. GRTC only have a single CC which is able to generate repeating events with the use of the CC0 interval register. I would...
Hi,
While completing the nRF54L Series Express course, I noted that USB support is not provided by the bare-metal SDK.
I wanted to check if adding support for this is...
I tried to build the Blinky sample description in nrf sdk fundamental academy training without success.
Error occur during build at B0n stage:
error: 'struct shell_ctx...
## Summary Setting `CONFIG_MEMFAULT_NCS_INTERNAL_FLASH_BACKED_COREDUMP=y` on an nRF54L15 target fails to compile. The Kconfig is exposed (it only `depends on PARTITION_MANAGER_ENABLED...
Hello, one of our devices moved from using the nRF52832 to using the nRF54L15 .
I created new board files and got the old software to run, after some adjustments. The application...
Hi everyone,
I’m working with a Zephyr input overlay where I define double-tap , longpress , and extra_longpress behaviors on the same physical button.
This is the overlay...
I am updating my ncs from ncs2.7.0 to 2.9.2. I have a dfu application for which the build targer is nrf52840 and nrf5340. For this reason, I have pm_static files. for some...
I am using SDK version v3.2.1 and trying to put the nRF54L15 DK board into deep sleep using the sys_poweroff () function and wake it up using Button 1 on the DK.
This setup...
I get this error when i try to use FATFS or LittleFS - RAM works though /Users/admin/mass_1/src/main.c: In function 'setup_flash': /opt/nordic/ncs/v2.9.0/nrf/include/flash_map_pm...
Looks like Gazell can't run on nrf52810 with nrf5 SDK :
I don't knnow whether it is possible to create app on it with nrf connect SDK.
I think nrf connect SDK will need...
Hi, I have purchase a circuitdojo_feather_nrf9151 board it has LIS2DH12 and npm1300 on i2c2 i also want to connect SHT40 but facing issue this sensor is not detecting on i2c...
Hey all, I wanted to enable shutdown and standby modes for this chip, but realised that I can not use the layer of zephyr. When i try to CONFIG_PM=y in prj.conf it does not...
Hi,
I'm running the system_off/ sample on v3.2.3 with these settings in prj.conf
And with this overlay file:
However, I can see that there's a high (and in fact...
