Hi,
1. How to set read protection and how to verify read protection for nRF54LM20B? 2. The test DK is PCA10184 0.7.0. 3. My test is as follows: Read protection will never...
Hi There,
I am currently developing an LTE-M application on nrf9151 using ncs v3.2.1, the device is a MQTT client that publishes telemetry periodically every 3 minutes,...
Hello Nordic Team,
I am working on an nRF52833 project using nRF5 SDK 17.1.0 with Secure DFU Bootloader.
Environment:
MCU: nRF52833
SDK: nRF5 SDK 17.1.0
SoftDevice...
Hello Nordic Team,
I am currently working with the nPM1300 EK together with the nRF54L15 platform and a custom 40 mAh Li-Po battery.
I am facing an issue while configuring...
i2c_write_read() returns -5 (EIO) immediately when writing register 0x01 to the sensor. Logic analyzer confirms the sensor clock-stretches SCL for ~14µs+ after receiving the...
I modified the "ble_app_uart_c" to connect HM-10 (using TI BLE chip CC254x) SPP peripheral.
Ignoring the filtering process (make function adv_uuid_compare(nrf_ble_scan.c...
Downloaded from Git Hub nRF ToolBox from GitHub project dated Nov 12 2018
Tried to build with Android Studio 3.3.2 JRE 1.8.0.152
But get build error
Error C:\users\maltr...
Hi,
I use the nrf52 to connect to a central using BLE 4.0 where power consumption is a sensitive issue. I want to understand how encryption will increase the Link Layer...
I use pc-ble-driver-master/hrc as central to connect the target device which runs with modified ble_app_uart hex.
I can discover service and characteristic correctly, but...
Hi
Getting problem in DFU feature while using segger embedded studio.Device gets programmed successfully but stops working after that.
I am following the same process...
I am trying add UART functionality in nRF5_SDK_11.0.0_89a8197\examples\dfu\bootloader.
After adding all required files and compiling program I am getting following error...
Hello I am using nrf52832 and I want to Calculate date and time at specific event periodically and save it to flash,so is it possible by using ble_app_cts_c example or any...
as title,
I can't load the project to SEGGER Embedded Studio.
I can't install CMake by entering the those command ( choco install -y cmake --installargs 'ADD_CMAKE_TO_PATH...
Hi
I was trying to do the page up and down key, I just built it successfully but it is no response.
Could anyone find out the reason for me.
I appreciate for your assistance...
Hello,
I tried to follow the "nRF_Sniffer_UG_v2.2" and i didn't understand the section 1.2 which described how to set the Python and Pyserial,can some one explain what to...
Hi,
1. Can one run the coexist sample with softdevice S132 on a mesh where all the other nodes run S140?
2. does the coexist (UART) example need to be provisioned. ...
Hello to everyone.
I'm working with the Light_Switch example with four nRF52832 SDK (two clients, two servers) and my cellphone as provisioner, in Mesh 3.10, with "nRF Mesh...
Hi again, Figure 106 in the OPS indicates that the application core and the modem core in the nRF9160 have separate Flash and RAM partitions.
Is this a "real" partition...
Hello,
I ordered my nRF52 DK from Rigado for their BMD-350 module using the nRF52832 chip, but their DK comes with an additional Atmel chip. Now I saw the regular nRF 52...
