Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Dear Nordic, I'm using TIMER21 for our library, but I encounter problems with CC channels 6 and 7: their compare events never fire. The problem I configure the timer to generate...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello.! I try nRF51822(softdevice using S130) SDK v12.3. I operate it as a master, but I leave it to distance to cut once and approach it afterwards, and, after a reconnection...
I need to stream 2 audio channels between two nRF52832 chips. I have two of the nRF52-DK boards and would like advice on which sample app might get me started in the right...
I have used 32khz and 32Mhz Crystal and across that crystal i have used 12pF capacitor. But unfortunately in market 12pF capacitor is not available in 0402 smd package.
...
In the SDK, there are examples for boards called "pca10028, pca10040, pca10040e, pca10056"
I have the nRF52-DK board, which of the above numbers does it conform too? Or...
Hello,
I am trying to adjust a peripheral device to connect a central device based on ble_app_uart_c example. Although this example has been discussed numerous times I was...
I am moving an SDK12 peripheral nus + central nus application to SDK14.
I am following the ble_app_hrs_rscs_relay example for SDK14 on how to setup the dual role ble event...
The nRF52832 OPS 0.6.3 describes the CONFIGID register in FICR. This is the same as on the nRF51822.
SDK 14.1.0 does not show this register in the NRF_FICR_Type definition...
Hi everyone, I've read some nordic forum articles on this topic but somehow I just dont get information I need.
I can flash my custom nrf51822 chip by using my nrf51422...
Hi,
I'm currently evaluating the use of the nrf52832 as an HCI interface with a linux host and realized from the various questions that the nrf SDK does not support the...
I am running on Uvision. 5.23.
I am running a Central on one PCA10040 DK and a Peripheral on a second PAC10040 DK.
When I run a first RTT Viewer V6.22 (with SWD Target...
Below is from SDK14.2.0 ble_gap.h
There is no white list variable.
/**@brief GAP scanning parameters. */ typedef struct { uint8_t active : 1; /**< If 1, perform...
I am developing a general case application for several devices I am developing. The application template will then be modified in small ways to support different hardware...