Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Dear Nordic, I'm using TIMER21 for our library, but I encounter problems with CC channels 6 and 7: their compare events never fire. The problem I configure the timer to generate...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everybody, I try to send nus_string data. I bought different inputs and outputs like this;
INPUT;
OUTPUT;
"aaaaa" received // Send 5 times "a"
INPUT;...
Hi team,
I looking for an example on how I can setup a mesh to send and receive string of characters from and to mesh nodes.
I have couple of nrf52832 modules connected...
hello there i downloaded nordic's new mesh sdk. i am using nrf51dk. in mesh sdk there is no keil project . only source file is given. can you tell me how to make project using...
Dear Nordic-Support,
my questions are in regard to the nRF52840 PDK and the SPIM-frequency rates.
The Objective Product specification lists possible configuration...
I would like to use an nRF52840 as a sniffer between my phone and an other nRF52840. I tried to follow the nRF Sniffer guide 2.1 but the firmware seems not working as LED1...
Hi everyone,
I am trying to advertise data from nrf52832 to a smartphone (nRF Connect).
Below are my advertising parameters.
ble_adv_modes_config_t options = {0};...
Hi,
What is the max timer frequency that the nrf52840 can handle in counter mode?
I see that the timer runs at max 16Mhz when in timer mode, is it possible to get 32Mhz...
Ok I’m new to ARM / Nordic and Bluetooth but after a bunch of reading I downloaded SES and the Mesh SDK and got the light switch demo to both compile and run on a few boards...
I'm looking for where the compiler is for the nRF52832....
I just need to compile code, and copy the binary to the device....do you have any pages which show, step by...
hai. I got thingy 52 from Nordic tech tour. now i would like to reconfigure it. for enabling all its sensor into RTOS(real-time operating system apache mynewt) with the nrf52...
I want to implement a ready line for SPI and I noticed nordic has similar code in your sdk: components/serialization/common/transport/ser_phy/ser_phy_spi_slave.c.
However...
Hi,
I am trying to send data to server using ESP8266 WiFi module interface with nRF52832 DK board via UART interface. My problem is when i sent AT command to ESP8266 it...
