An external MCU occasionally sends data to the nRF54L05 over I2C. Between transfers, the nRF54L05 should sleep and wake when addressed, without a separate wake pin.
What...
On a custom Zigbee End Device application for the Thingy:53 (NCS v2.9.3), ZCL Configure Reporting commands sent by Zigbee2MQTT are rejected with ZCL status FAILURE for almost...
Thanks in advanced. I'm immigrating projects into NCS bare metal v2.0.1. Sample Bluetooth ble_nus only advertises for 3 minutes, then device can't be scanned again. I check...
Hello,
I'm following online courses in Nordic Academy (nRF Connect SDK Intermediate).
As indicated in the first lesson,first excercice, I added device_message_queue...
nRF54LM20 + nRF7002, NCS 3.4.1: SoftAP provisioning and station low power in one image
Our battery-powered product (no BLE antenna), removed due to space in the PCB and...
Hi
Have you done any benchmarking to estimate the difference in power consumption when comparing the nRF9151 in NTN mode vs LTE-M?
In particular I am curious if NTN has...
Dear Nordic Team,
I want to know if we can support the real time talking like phone call between peripheral and central by software device. On application layer, we just...
As I have provision a nearby light server, use those serial commands:
In [1]: p = Provisioner(d[0])
In [2]: p.scan_start()
In [3]: p.provision()
How to provision...
I'm building wih Keil MDK-Lite Version 5.24.1 and I just copied the examples for gpiote into my own folder, everything was kept the same (ie copying from C:\Nordic\nRF5_SDK_14...
Hello. I tried to use UART speed 115200. But my slave does not response. I connected slave to the arduino and it is working corectly. I got 2 oscillograms . From arduino and...
Hello everyone,
Currently I'm altering the "ble_app_uart" and "ble_app_uart_c" examples (both under examples/ble_peripheral) to suit my needs. What I currently need to...
Hello,
I have interfaced one sensor with pca10040. I am using sdk 12.2.2. I am sending the data from sensor in advertisement packet(manuf specific data). Now my sensor data...
after the advertising timeout occurs the board goes into sleep mode and then immediately runs from the top of the main function. I know that a pin state change can wake up...
Edit: Rephrased the question to make it easier to answer.
I used flash storage to store a couple of variables between resets in a app made from SDK 12.2, now I am attempting...
hi,
i need to reconfigure the WDT and also change the timer value in WDT. is it possible to do that.
i tried but i can not.
1.configured wdt with timer 5sec.
2.i...
Hi guys,
we are developing firmware for nrf52832 SoC based on the mbed platform.
The firmware uses BLE and few peripherals (timers and pwms). Since our goal is to build...
Is it possible to scan and make Gatt Connection simulataneously from Android app to NRF device.I have seen issues in second connection after disconnection.I have seen second...
Question for I2S.
Execute follow.
[TXD.PTR set A] 1st
[START]
[TXPTRUPD event] (not set TXD.PTR) 2nd.
2nd transfer address use A?
How long time between...
There are a few setting options I would like to keep through power cycle like sensor sampling rate, continuous sampling on/off, etc. I had success implementing saving of one...
I'm using a PCA10056 (NRF52840 Preview DK) v0.9.1, and trying to erase the existing firmware, but running into issues.
I've tried nrfjprog -f NRF52 --eraseall with version...
Hi
I am running some thing similar to the multiprotocol ble_app_gzll example but using freeRTOS and peer manager. Effectively the the main in ble_app_gzll example is a...
