Running a test that sends a small ping packet to a server about 1/minute and I'm seeing intermittent board resets. I'm still trying to track down the cause, but in one case...
Hello Nordic support,
We are designing a battery-powered device using the u-blox NORA-B206-00B module, based on the nRF54L15. u-blox support recommended contacting you regarding...
Hi Nordic DevZone,
We are currently looking at how best to handle nRF9151 programming in mass production, and I would like to understand Nordic’s intended approach a bit...
Hello, The nRF9151 hardware design guidelines (power sequence) require VDD_GPIO to be applied at least 6 ms after VDD and ENABLE, after the hardware boot. In our design a...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
nrfConnectSDK V2.8
Toolchain
Board: nrf5340dk
Hi, while compiling ncs-spi-master-slave-example , I am getting below errors
In function 'spi_init': C:/Users/hello...
Hi,
EDITED: This appears to NOT be related to any open circuit, the SAME behavior comes even with abrupt changes to the current scale, without any interruptions. Additional...
Hi.
code base is sdk 17.1.0
MCU : nrf52810
Softdevice : S112 (7.2.0)
use SES 5.42a
step1. modify NRF_SDH_BLE_GATT_MAX_MTU_SIZE form 23 to 50 in sdk_config.h
...
Dear nRF experts. We are a module manufacturer and we have designed an nRF45L15 module. We are doing a series of verifications. When we were doing the connection test, we...
Hi,
I use Nordic connect SDK and have to create a new revision for a custom board, because there are some hardware changes. I managed to create an overlay for the new revision...
MCUBOOT contains a flag MCUBOOT_OVERWRITE_ONLY_KEEP_BACKUP that stops it erasing a big chunk of the start of the secondary image after an update.
We would like to set this...
I'm looking for an nrfutil command to replace this command:
nrfjprog --memwr 0x10001080 --val 0x12345678
My goal is to write a serial number to the UICR CUSTOMER[0] register...
Hi All,
I have nRF54l15-PDK board which has 8MB of external flash. Currently I am exploring on basic read/write functionality on external flash.
I am using nrf sdk version...
I'm checking the function by uploading the code to the pcb that uploaded the nrf9160 chip.
I checked that the network communication is normal on the previous 9160dk board...
Hello,
I have just received the nRF5340-DK development kit. However, when I plug in the USB cable to my PC, it's not detected. I have tried multiple USB ports and the issue...
i'm working "bare-metal" with the nRF54-DK, loading from the command-line by directly calling JLink....
often (but not always) i receive the following message from JLink...
Hi there
I'm using two nRF52840 boards and I want to set them up to relay a message from one phone to another like this: phoneA > board1 > board2 > phoneB.
I have looked...
In attempting to set up the nPM1300-EK for battery characterization, I keep seeing the connection status "PMIC Not powered" and repeating errors: "module_pmic: No response...
Hello everyone,
I am working on a project using the nRF52840 with Zephyr and SDK 2.5.2. Recently, I sent a request to register my company for Bluetooth, and I received the...
I am using "nrfjprog -p" to reset our nordic devices in our test rigs. We recently migrated the setup to RHEL 9 and now we are seeing regular failures in nrfjprog due to ...