Hi Sirs
We are planning to use the nRF54LM20A/B together with the nRF21540 FEM in our design, and we have a few technical questions regarding TX power control and FEM...
Hi Nordic Support Team,
We are currently evaluating the nRF54L05 DFU single-slot sample in NCS v3.3.0.
Our question is: Is it technically possible to configure the single...
Hi,
I'm using the published nRF54L15 DK hardware files and noticed something that I don't understand.
On the nPM1300 section of the schematic and PCB:
Pin 20 ( VSYS...
we are developing solutions with PMIC type=PM1300, we eager to know the internal LDOs PSRR.
i have read 171 page of PM1300 datasheet, but cannot find PSRR data or the PSRR...
nRF54L15 PDM clock runs at ~1/32 of expected (PCLK1M instead of PCLK32M) on a custom board - works on DK
Summary
On a custom nRF54L15 board, the PDM peripheral clock ...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update.
if 1 step is done, application update...
hi,
We development a remote control as same as Apple TV 4th remote control. I am interested in "nRF51 Smart Remote 3". How do i download the nRFready Smart Remote 3 for...
Hi,
I am facing an issue with the nordic 51822. I am declaring a gpio as output. I am writing logic High to that pin. When I check the signal in logic analyzer and multimeter...
Using rev 0218 firmware I am getting an awful lot of device errors with the mbed kit. I am not sure if this is a Nordic or an mbed issue so am asking in both places. Symptoms...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
I'm testing SPIM of nRF52 on PCA10040 using S132 and SDK11.
Its base on the app_peripheral_uart example, so I already have BLE communication.
When SPI is not initiated...
I have just received a nRF52 DK board and I am as a start trying to compile the associated Blink program in Keil 5.18 Lite. When I copy the blink example using the Pack Installer...
hi,
I was reading documentation and forum but failed to get a clear picture how AES module work.
So far my understanding is:
There are two ways to access AES either...
I'm building a product that can use the features from your Smart Remote 3. Is there someway to get the reference source files so I can adapt some of the smart remote features...
Hi,
Few days ago I received my DK-52, I set up the development environment based on Keil and started to compile some of the examples included into the SDK. I have not a Windows...
I have been googleing for a solution but have not found any solution yet.
Have tried the following:
Installed J-Link commander. (Does not pick up any usb devices...
We are a newbie team developing some measurement tests with the nRF52832 DK in order to evaluate the BLE from nRF52832 QFAA80 (s132 and pca10040) for IoT applications.
...
hi all,
Question:
i want to print "BUTTON IS PRESSED" continuously when button is pressed and i want to print "BUTTON IS RELEASED" when button is released.
eg: if i...
