Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
Hi there
I started with an empty ble_template and added my own custom service emulating the batterey service, with all the same functions etc. Using master emulator i can...
I have a project in which I've started from the proximity app example code and added some UART stuff using app_uart.c. The linker is giving me this error immediately after...
Hi,
I'm trying to get an iOS app to connect to a Nordic BLE device. I'm a firmware guy with little app experience but I have gotten a app to work based off the code presented...
Hi,
Im new to BLE and still trying to wrap my head around things. I am using the both new nRF51 DK and nRF51 Dongle for testing at the moment. I know that the old dongle...
I would like to have track time of the day in my peripheral (s110)application. I understood that RTC0 is used by Soft device. RTC1 is used by app_timer application. I have...
hi nordic:
thank you for your great support!
question 1:
App: LightBlue in iOS.
when app scanning for perpherals ,i have found my device,show as "measurement…."
THEN...
Hi all,
I had a working TWI connection combined with BLE advertising. When
I added uart code for printing to putty this TWI connection was no longer functional.
So...
Hello,
I am currently working on a project and I would like to add some security to my device by preventing services from being discovered. Ideally when a user connects...
Hi
I am trying to use the internal ADC to capture an analog value every second. For this I use a timer to wake up every second, start the ADC and go back to sleep.
I...
Is anyone using the third-party BLE module from Taiyo Yuden? If so, where did you find the recommended footprint?
Taiyo Yuden's website only gives very limited information...
In the SDK 8.0 are only examples for nRF51422.
Is it possible to compile this for nRF51822 and is the softdevice 8.0.0 for both controllers?
Best regards,
Roman.
Hello,
i am new to nRF Bluetooth.
My Setup ist:
One Atmel atmega640 and one nrf51822 communication via UART (at the moment).
I am sending data from atmega640 to...
Hi,
I'm writing a bootloader for nrf51822 to be able to update the nRF51's firmware through SPI (data transferred via an STM32 retrieving the file through USB).
My idea...
Hello,
I am trying to write data to flash with the pstorage api. I managed successful to write data to flash with the pstorage_test_store_and_update() function from the...
Hi
Recently we bought NRF51 DK board. Initially when i connect the nrf51 DK board to PC via USB it mounts JLINK driver and on IF/BOOT button it mounts BOOTLOADER drive...
