Setup: nRF Connect SDK v3.4.0 (LTS), custom board based on nRF54LM20A, sysbuild with MCUboot as the only bootloader (no NSIB / b0), DTS partitions (SB_CONFIG_PARTITION_MANAGER...
Hi,
We are designing a battery-powered product based on two Nordic chips and would like your recommendation on the overall architecture before we freeze the hardware, having...
Hi,
GSMA SGP.32 v1.3 section 3.8.2 and 3.8.4: the device selects IPAd or IPAe mode with the TERMINAL CAPABILITY command at UICC initialisation. Tag 84 , byte 1, bit 1 set...
Hello I'm developing a project that would communicate with a cellular module using AT-Commands, and voice data using PCM, these cellular modules are always using PCM Short...
Problem:
After every wake-up our device reports a SoC 10–28 % higher than it reported just before going to sleep.
Between sessions the nRF5340 is in System OFF via sys_poweroff...
Hi Nordic team,
While benchmarking quantized INT4 (`s4`) matrix-vector multiplication (`arm_fully_connected_s4` / `arm_nn_vec_mat_mult_t_s4`) on an **nRF54LM20 DK (`nrf54lm20dk...
I'm aware of https://devzone.nordicsemi.com/f/nordic-q-a/125252/reset-over-ctrl-ap/555253?focus=true
Is it possible for an nRF54 to safely use the CPU access to the AP registers...
Hello,
I am not much of a PCB designer but want to tinker with nrf51422 EK Altium designer files provided. I try to open the project file using Altium designer 14, but...
Hi all,
I am new to hardware design and would greatly appreciate pointers. We intend to use mini-USB port for charging/power supply rather than for data. What is the best...
Hi all,
I am using NRF24LE1 32pin.
Does anybody know can I apply on XC1 pin external frequency different from 16MHz if I am not using radio module??? Thanks.
I am currently using the nRF51422 DK along with the nRFgo Starter Kit. I followed the instructions in the PDF "nRF51422_DK_UG_v2.0," and I attached the nRF51422 with PCB antenna...
use keil to download code to flash fail
use nRFgo studio to connect target device error
Load
C:\Keil\ARM\Device\Nordic\nrf51822_v5.0.0.34603_Backup\Board\pca10001...
Hello,
when using Keil's ULINK Pro debugger V1.57 connected to PCA10006 board for debugging nRF51822 code the ULINK is recognized by µVision V5.1.0.0 but the FW download...
I have an nRF51822 (256KB) that I want to program with some data targeted at 0x20000 to just under 0x38000. My code starts at 0x16000 (allowing for S110) and is only 1700...
I have a nrfgo 6310 start kit that I use for my nrf51822, but I'm wondering if I can also use the nrfgo 6310 for the nrf24Lu1 development kit as well? I tried plugging in...
Hi All,
I am working on the S120 bootloader.
I start it with dfu sample on nrf6310 folder. It work with S110 softdevice with PCA10001 perfectly.
I had made following...
Hi,
I would be grateful if someone could guide me a bit.
As far as I understand, nRF24L01+ implements Enhanced Shockburst technology in chip. To use nRF8001 as drop in replacement...
Hi all,
I am using s110 v7 for scanning and advertising, it works well. Now, I would like to measure RSSI while scanning (already scanned device but not connected) . Can...
Hi,
I am using nRF5182. Kiel is the IDE. I need to operate the device in 25Mhz. How can i change the clock frequency to 25Mhz. Is it possible? Will it affect the operation...
Hi,
I just stumbled upon the nAn-36 note ( www.nordicsemi.com/.../80193304 ) and I have two comments about it :
I think it's the best technical documentation I've...
Where to find definition for INTENSET/CLR for TIMERs in 'nRF51_Reference_manual v1.1'? I think I've read it all by now, but still can't find it.
After some digging I found...
If I have the PC insert 1msec byte spacing between data bytes sent to the NRF51422, it receives the message and doesn't reset. I can send messages less than 10 bytes to the...
