I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
Hi All,
I have to implement an I2C Slave on my nrf52833 BLE project which is currently working (SDK 2.9.2)
I need some confirmation with the following step:
I have...
I am using the 54l10 chip, and after compiling the project, I will receive a hex firmware and a zip update package. The bin firmware and hex firmware in this update package...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
Hi,
I'm using the nRF52840 with the SoftDevice for BLE. In my system, it's primarily a BLE transceiver controlled via SPI by an external TI MSP430. We're considering implementing...
Hello Everyone,
Can anyone give me recommendation of a BLE App for Eddystone TLM (with temperature)?
Till now, I used the Beacon Manager. But I think the App has a problem...
The gpio specifications table lists 3mA for VDD greater than 1.7V and 6mA for voltages greater than 2.7V but what about in between?
Would a linear approximation between...
Hello,
I am trying to fix the UART communication error in a peripheral side.
First of all, the setup that I am using is as below.
[SDK] nRF5_SDK_11.0.0_89a8197
...
We would like to enable the flash protection for an nRF52 application with the typical scenario:
to disable flash reads from the JTAG,SWD interface; only erase/reprogram...
Hello everyone.Recently I try to send some information from a "nrf51822" to phone when they are connected .So I choose "ble_app_hrs" example program,and I add two characteristics...
Hi everyone
I am working with nrf51 and I need to know how much my specific code occupies in the flash memory (I know how much is the available memory).
Thank you
I have two board - 51422AC based PCA10028 and 51822AA based custom board. Custom board doesn't have 32768 OSC.
My goal is to let custom board work with example project...
I want to use my stand alone SEGGER with nRFgo Studio. How do I do that?
It looks lite nRFgo Studio only recognises the PCA10028 board as a SEGGER but not my stand alone...
I have a ble_uart application which is working when I load it on the chip. But it will not automaticly run again if I unplug the supply and just plugin again. When I unplug...
hi,
i am using eclipse IDE to build the blinky example with soft device s130(using SDK11). i added the make file and .ld script and linked all files which is required....
Dear Nordic family,
I tried programming Raytac MDBT40 with the LED blinking code (taken from the example project of SDK 8) which worked with nRF51822 Bluetooth Low Energy...
Hi
I have been using the DFU for quite a while. I adapted the boot loader to my hardware and compiled it using Keil.
All my other code is written in another environment...
Dear Nordic Developers!
When I call the sd_power_system_off() function to put the MCU to system OFF, after that I can still see the advertiser device in MasterControlPanel...
Hi!
First of all, I'm using the nrf52 PCA 10040 DK, with SDK11.0.0, and my Soft Device is 132 2.0.2.
I'm developing an app for comunicating with a sensor via SPI (send...
