Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I have an nRF52832, coding with SEGGER and the SDK 14.2.0. I'm trying the ble_peripheral/ble_app_uart example (although I get similar results with the other BLE examples)...
Using a pushbutton while advertising, the GPIOTE_IRQHandler handles the pushbutton click OK, but then the processor resets. The RESETREAS is code 4, aka. RESET from soft reset...
Hi,
I have couple of queries that need to be sorted,
http://www.nordicsemi.com/eng/Products/S112-SoftDevice, Says that S112 supports 2-peripheral connection and 1 broadcaster...
I want advertise the peripheral periodically only. i implement the logic it is working fine.but my doubt is once i connected to connected to central device advertise is no...
Noted the difference between the layouts concerning antenna matching among DK 0.9 and DK 0.11.
DK 0.9
DK 0.11
The screenshots are for L3. Differences between...
Hello,
I have a requirement to implement the following functionality. Can this be done?
Basically i need to store some customer info on the NFC NTAG. This has to customizable...
I am using nRF Connect for desktop v2.3.0. In my DIS service Firmware Revision String characteristic I am using a string of 30 characters. But when I connect to my device...
Hi,
We are looking into developing a device based on 52832 platform.
How many devices (phones) can be paired with our device?
In other words: How many pairing keys can...
See attachment - enlarge if it's too small. How can I get nRF Connect on my Windows 10 laptop to bring more than 20 characters, and also print in text (instead of hex values...
I would like to know the part number for the Side facing RGB LEDs used in the Nordic Thingy 52. I couldn't find the Bill of Material for the Thingy 52.
Hi. I got TCA6424A IC which communicates through i2c. I tried to use that with nordic but it doesnt respond. I used simple twi scanner application which should print address...
Dear nordic employee
My 52832’s GPIO control the external 32mhz crystal‘s power，
when the 52832 work in the sleepmode ,I cut the 32mhz crystal'power
then when I want...
Hi I have a problem with TWI (the slave part), that is, we can only receive on nrf52840 8 bit, there is someone who knows how to do so you can receive 16 bit, we have taken...
Is there possible to get timer period shorter than 12us with nRF51 and SDK 14? "timer" example with PCA10040 works correct, but with PCA10028 not. When set timer period lower...
