Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I'm new to nRF51822 Evaluation Kit. I was able to build the hex from "ble_app_hrs" example with GCC and Eclipse. However, it won't allow me to flash it by drag and drop to...
Hello, I'm an developer using nrf51822.
I have the same problem with this.
devzone.nordicsemi.com/.../
But this problem has no more discussion...
Here is my problem...
First I load soft device through nRFgo.
Then I run debug with eclipse.
I then step through code in main.c ...
(I'm using QFAAG0 chip)
Stepping worked fine when I used...
Hi,
I use a system with BLE softcore running - and can generate highly precise pulses with the gpio pins using Timer1+2 with interrupt service routines. Jitter might be...
Hi,
I want to use nRF51822 to do some development in the eclipse.I follow the document(nAN-29 nRF51 Development with GCC and Eclipse Application Note v1.1) step by step,when...
Using PCA10001 Evaluation kit, SDK v6.1.0_b2ec2e6 and SD s110_nrf51822_7.0.0
IOS app nrf Toolbox HRM on iPhone. Everything is working fine, get the advertisement, connect...
Hi all,
Short version: I want to make 200 devices using nrf51822 (and S130 v0.5.0-1alpha), all advertising/scanning at the same time, and process RSSI readings for proximity...
I am trying to find out what is the difference between nRF51822-mKIT and nRF51822 EK . Visually both of the boards look identical and the only noticeable difference is an...
I just tried setting up on Windows8.1 but can't see the "nRFgo Studio".
I got as far as step 4 on page 9 of "nRF51822 Development Kit User Guide v1.4",
but it doesn't...
I have a RedBear Blend and I want to talk to it from iOS.
I'm currently using the default setup provided with the Blend and RedBear's library over the top of the Nordic...
Hi, after a deep study of Datasheet I was finally able to have two 24L01+ talk to each other with a PIC18 program.
Now I need to make a step further using ACK Payload since...
Hello,
I am trying to verify hid_keyboard_demo app running on nRF51822 with android running device.
I have tested it with my phone running android kitkat and windows...
hiii.....
am doing a project for implementing broadcasting while in active connection... i hv broadcastd datas successfully but the problem is when i disconnect the connection...
I am unable to see any uart print output when running the uart_example with NRF51822. I am able to see the program execute via the debugger, but have not seen any output....
