Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
I have created an instance of time using the standard time function in C. I have also linked it to a counter on a timer so I can track how long the device has been active...
At CES this year (2018) there was a booth showing essentially a roughly 1/4 size Thingy:52. It wasn't actually at the Nordic booth so I'm not sure if it was actually a Nordic...
I think there's a problem with the beacon advertisement sent by Thingy52. I'm seeing the problem in my own PC code and also air sniffer. The advertising data packet looks...
I am using nrf_fstorage_read command to read data from flash. I have defined my start address as 0x68000 and end address as 0x72000.
I erase the memory through nRFgo studio...
Hello,
I've searched around the forum and followed all the advice given in other threads but am still not having any luck.
I've tried running the nRF sniffer on both a...
Hi there. I just got the nRF52840 DK and am trying to get going with it. I have been looking at this getting started page:
https://www.nordicsemi.com/eng/Products/Getting...
Dear lovely people!
Setup: sdk14 / s132 v5 / nrf52832
Just like with the previous SDKs, I tried to make a multilink nus central fw.
The periph device runs my code based...
Hello,
In our application we heavily use the application scheduler. This was done for 2 main reasons:
serialize access to system resources
enable the soft device to...
Good Afternoon,
I'm writing some config data on an empty record the first time I turn on my board and updating that same record every next time I turn on the board.
...
Hi everybody I have a couple of questions regarding power consumption for the nRF 52 DK Rev. 1 (nRF52832). I currently have an application where I sample 12-bit ADC data via...
I'm working on support for several custom characteristics that require long write support. I'm using the nrf_ble_qwr library, and I've noticed what seems to be a discrepancy...
Hello,
I have an nRF52 DK here that behaves strangely since a few days. Hardware id is 0xc7
When I boot it up with my firmware, sd_ble_enable takes around 2 seconds...
Hi
We have used DTM functionality in nRFgo Studio to carry out signal strength testing during the design stage. We now want to automated this testing in end-of-line testing...
Hello,
I beginner for Nordic board, developing small device using BLE.
I build softdevice, bootloader and application. I checked working DFU mode(via serial, not BLE...
What a software i can use for develloping a Bluetooth Profil Mesh (BLE5) ? Hello every body , i want to develop a bluetooth mesh profil and i don't known which a IDE i will...
