Hi everyone.
I cutted PCB track shorting solder bridge SB40 .
I connected like this..
Then I opened power profile kit 2. I am using amperemeter..This is my app scrrenshot...
Hi team.
Now i'm use soc nrf5340, and the ncs version 2.9.0.
I want to encrypt my external flash using QSPI.
I encountered some problems while using the nrf connect...
Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Hi,
I'm using pstorage, but found some problem. sd_flash_page_erase will not trigger system event after the operation is complete.
In my code, I registered the system...
Are you supposed to be able to nest critical regions using CRITICAL_REGION_ENTER and CRITICAL_REGION_EXIT? Here I mean you have a function which uses a critical region to...
I'm trying to run bootloader from nRF SDKv6 with SDv7 in gcc.
On our custom board, it runs, but does not advertise (sd_ble_gap_adv_start gets called and does not return...
Hi,
I have developed the firmware using nRF51822 Development Kit. I now want to get to put the firmware on nRF51822 chip used in breadboard. I got a smt adapter with nRF51822...
Hi!
When trying to update app using example bootloader for s110, v.7 from nRF Toolbox I get "Device is not supported. Check if it is in the DFU state".
Bootloader is...
Good morning,
In the application I'm developping with nRF51822 anb S110 SoftDevice, the final peripheral product will be installed in a physical non-accessible place. So...
Hello,
I'm working with the example ble_app_multilink_central of S120. In this example, the scan is done correctly in the three channels of advertising?
Thanks!
I have a characteristic which is a long string. I need to be able to read and write it.
Below is the function for writing to start with. Please comment on this function...
It appears version 7.0 of the SoftDevice 110 supports over the air flashing of softdevice/bootloader/application or a zip containing a combination of the three.
Trying...
Hi,
I'm trying to get SPI (master) to work (nRF51822) for communicating with a quadrature counter (LS7366R).
I've read several implementations of SPI master, such as the...
Using:
GCC 4.8
pure-gcc Setup
Sdk 5.2.0
Softdevice 6.0
I execute some code within interrupt context (softdevice handler) and also in main thread.
I need...
Hi,
What's the difference between a 0.9.0 pca10000 firmware and the earlier version (0.8.0)? I noticed that the throughput with 0.9.0 on the same dongle is much less than...
I'm trying to use the TWI master example with the S120 soft device. It looks like there is a known problem trying to get the S110 working with the hardware TWI. It seems the...
Hello.
I want to make flashing of devices for production faster.
So I want to write application together with bootloader via J-Link simultaneously and not via OTA DFU.
...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
