While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Hi Nordic team,
I am working on a custom board based on the nRF54L15 using nRF Connect SDK v3.1.0.
On our hardware, the nRF54L15 has a 32 MHz crystal connected to XC1...
Hello,
I am using the nRF9151 DK with the Serial LTE Modem (SLM) application.
I put the device into sleep mode using:
AT#XSLEEP=2
This successfully disables the UART...
Hello Nordic team,
We are reviewing our nRF54LM20-CAAA (CSP61) hardware design and would appreciate your clarification on several power and RF related points.
DECRF...
Hi,
I have a question regarding the SAADC timing parameters.
I could not find an official specification for the SAADC power-up time (t_PWRUP). While measuring it on my...
Hi all — I'm developing a custom nRF5340 development board (Raytac MDBT53-1M) and would value the community's honest read on whether it's worth producing.
The goal is...
Hi,
I've started using the nRF5 11.0.0 (89a8197) SDK on a board that does not include an external low-frequency CLK source.
When using the nRF52 0.9.2 SDK, we were recommended...
I want to reserve a section of memory, FLASH, that will hold static, read only, product data. My application makes use of the following parts of the Nordic ecosystem.
...
I would like to carry out communication with a plurality of peripheral using a central multi-link function.
When performing the communication via the relay unit, the communication...
Hi ,
I'm intrested in using the BLE UART apllication provided by Nordic for the nRF51 422 developpement kit and I have a little question to ask and please forgive its simplicity...
Environment is a PCA10040 v1.1.0, measuring current with a Rigol DS1104B over a 10 Ohm resistor.
I'm using the ble_pwr_profiling example from nRF5 SDK v11. I've programmed...
Hi,
i;m trying to build the "nrf52-ble-app-lbs" example which i downloaded from git hub github.com/.../nRF52-ble-app-lbs.
I followed the instructions in the README file...
I want to connect to the wired sensor NRF51822 board, whether it is possible to adjust the findings for the closure, they sent a message to the application?
Hi, I've recently switched from the older SDK 6 to SDK 9. However, I am unable to get my NRF51822 working with any of the example projects. I've managed to compile the projects...
Hi, I am working on eddystone project i.e nrf5-sdk-for-eddystone-master which is newly released by nordic. And I set URL,UUID and TLM frames successfully but when I trying...
Hello,
I am encountering a very strange problem with the Timeslot API.
I am developing with s130 and using the timeslot example provided by Nordic to
send data revived...
So far I've been prototyping everything on an Arduino Zero connected to a nRF24. Is switching to an nRF51822 an option for me? or will I have to switch my entire code to work...
I need to communicate with several nrf modules, 1 rx and at least 2 rx. I started with nrf24l01 but it has no rssi. For that reason i bought nrf51822.
What i have to do to...
hi,
i have doubt regarding NRF 51822BEACON KIT [pca20006 board],
......i want to configure it in all ble modes [central,periperal,broadcaster,listener],
how can i do...
Hi,
I want to add DFU OTA feature for my project, I use SDK 6.1.0 and S110 7.1.0, I found a sample Bootloader code for different version of SDK (SDK 6.0.0), from Github...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
