We have two organizations/projects in our nRF Cloud account:
Jackwoida 51789c46 Team (retain)
James_Eval (remove)
I am the account owner/administrator. The James_Eval...
i'm writing bare-metal code for the FLPR (which was loaded by a bare-metal launcher running on the M33)....
when my FLPR code "idles" using the WFI instruction, power consumptions...
I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
I have tried to create delay_timer function using app_uart as nrf_delay replacement in order to save power as much as possible in a short delay existed in any part of my code...
I tried all the examples TWI code on my device and a dev kit nRF51-DK. Nothing appeared to work, either I get a into the WDT handler or the nRF51 resets.
While combing...
Hello,
My name is Mehdi, and I am a student in a french university. Actually, I am working on a project and I aim to use the Heart Rate for a statical studies to use it...
Hi,
I'm trying to use the NRF24L01 as a replacement to HS6200p. But I can't find 0x1E (SETUP VALUE) and 0x1F (PRE_GURD) in the NRF24L01 datasheet. Actually, in the datasheet...
Hi everyone,
I am using the following:
*nRF51422
*SDK11
*keil uVision 5.17
*s130
I have been working with nRF51 that scans beacons and stores it into persistent...
Hello everyone,
I am trying to set the security parameters for bonding with PASSKEY (static)format it is getting executed very well(connected and bonded) for the SDK 9...
Dear all:
My device uses LDO mode and DC-DC mode respectively, and the distance is different.In 4dbm, the distance of the LDO mode is 110m, while the LDO mode is in the 70m...
Hi,
I was wondering if anyone could clarify why there are enable, set and clear (CHEN, CHENSET, CHENCLR) for the PPI channels when according to the data sheet they all...
I checked S130 document for using nRF51822.
I want to change the nRF51822 like the following mode.
peripheral => central => scanning => peripheral => central => scanning...
Hello
I am trying to change the ticks value of Battery measurement interval (ble_app-prox example) but i am not able to understand how the ticks period is measured based...
Hi,
I was seeing memory leak issues when using NRF51 with JLkink v4.98. See this link:
forum.segger.com/index.php
This issue has been fixed with the latest version of...
The address miss event is not shown as a transition in Figure 22 of the NRF51 Reference Manual. What state does the NRF51 enter upon an address miss and how long after the...
To use BEL application, the soft device must be downloaded before programming.
i can find a table shows that which soft device version is suitable for chip version.
how...
Our application is developing RC units for small (indoor) model airplanes - we want to be able to have multiple planes flying at once without "stepping" on each other.
...
