Hi, I am using nrf52840-based custom hardware and have an external flash connected on SPIM3. Till now I was working with my other peripheral connected on different buses and...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hello,
We are currently evaluating a very low power application using the nRF5340+7002. Our hardware design includes a complex power supply configuration, and we need to...
Retrieving Custom Firmware Version from nRF52 BLE Controller to nRF9160 Host
Product: nRF Connect SDK v2.6.0 Hardware: nRF9160 (Host) connected via UART to nRF52832 (Controller...
Hello,
I recently got a BL653 Click Board and am trying to program it. As I do not have a supported MCU for the NECTO Studio IDE (the ClickBoard's manufacturer IDE), I...
Hello,
I am designing a custom PCBA based on the nRF7002DK PCBA and I really need the Fabrication Notes / Drawing that officially went to the fabricator to direct the build...
Hi All：
I'm working on ios ble midi proj. I have modified ble_nus code for my proj, I was modified the correct service uuid ,characteristic uuid , connection_interval ,latency...
Hello
I have recently downloaded SDK v10 for nRF51822 development using Keil uVision 5.14 IDE.
I am wishing to combine SPI slave function with custom BLE services/characteristics...
We are trying to find a way to send the High Frequency Clock directly out to a gpio pin. The reference manuals don't seem to have anything obvious.
Is there a way to do...
Hi,
I am trying to use PStorage to save simply 40 bytes of data onto a flash drive but for some reason the PStorage handler never gets called when I try to store and clear...
Dear all,
I need to measure a pulse width on a GPIO pin which is in between 100mseconds and 7.2 seconds long without the use of "regular" timers due to low power requirements...
I have migrated a new project from SDK 9 to 10, and now I seem to be having issues.
I'm using the uart_fifo to read data from a GPS, so the data shows up every 1 Second...
I would like to use pstorage to store some data.
From the developer zone I know, that the softdevice has to be used for pstorage.
I'm asking me, what will happen with...
i downloaded source code from github.com/.../nrf51-ble-app-lbs . and i am getting error like C:\Keil_v5\ARM\PACK\NordicSemiconductor\nRF_DeviceFamilyPack\8.2.0\Device\Include...
my issue is that when I use the bootloader to get DFU working it advertise DfuTarg and doenst show my services. I searched for hours, I found many answers and none worked...
Hi,
I am developing an application on nrf51822 chip. I have set
#define SEC_PARAM_MITM 0
#define SEC_PARAM_IO_CAPABILITIES BLE_GAP_IO_CAPS_NONE
Also i am developing...
Hi Nordic support,
I want to use the OOB key pairing and I found the below discussion:
Set OOB key on Master Control Panel?
This means I need to implement the application...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
I am trying develop a project in which when we request a characteristic from phone( read request), we will read data from other module through UART and give reply back. I...
Hi,
I designed before my board for 2 layer PCB and i used the coplanar waveguide with ground-plane in the bottom. now i want to move to the 4 PCB layer and i choose the...
