I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello,
We are in the final stages of development and are trying to tune our device to perform its best in noisy environments:
We are using nRF52833 SOC as a central...
Hello,
We are using 2 nRF5340-based devices running:
samples/bluetooth/periodic_adv_rsp
samples/bluetooth/periodic_sync_rsp
with the PAwR configuration (modified...
I am evaluating the board nrf3054-dk + nrf7002-ek I build and run the sample project net/samples/wifi/shell on my board when I compiled the project, I added the following...
The blinky example from the official website can be programmed, but after opening the code and compiling with SES to generate the hex file, it cannot be programmed. An MBR...
I think variations on this question have been posted before but they all seem to be very old. I'd like to use the Bluetooth 5.2 LE Power Control features that involve exchanges...
I am evaluating the board nrf3054-dk + nrf7002-ek I build and run the sample project net/samples/wifi/shell on my board I tested the wifi shell with some personal encryptions...
Hi!
I just upgraded a product we developed using a Fanstel BT840X module (nrf52840 with a Skyworks SKY66112 amplifier) from SDK 2.3.0 to SDK 3.1.1 and I noticed that our...
I'm planning on using an e-ink display with my custom PCB . But when I add/enable the e-ink display node in my device tree, the TF-M code throws an exception in /ncs/v3.2...
Hi,
The attached screenshot shows a section of an air-trace for the 5340 running a commercial LE Audio stack. From the rising edge of the logic inputs, it can be seen that...
Hi List, I am using ZMS to log data. While performing stress tests, I see few issues:
Including zms in the projects makes the application boot time delayed. The delay...
Hi there,
Several examples of the course include a configuration file and an overlay file for the nRF52840 dongle. However, the code cannot be compiled. The problem seems...
Hi everyone,
I’m trying to use the HTTP client sample from NCS v3.0.2 with a W5500 Ethernet shield on an nRF5340. DHCP works fine, and I can successfully POST and GET using...
We are using the Murata Type 2FR dev kit - https://www.murata.com/en-us/products/connectivitymodule/wi-fi-bluetooth/overview/lineup/type2fr
Internally, this has NXP's RW612...
I'm running the subrating sample (ncs\v3.1.1\nrf\samples\bluetooth\subrating) on two nRF54L15-DK boards. Using a protocol analyzer I'm seeing that when the subrate factor...
