Hello,
I have set nRF51822 Evaluation Kit. With its help, I would like to read the pulse of the heart rate monitor:
link text
I manage to connect to it using the...
Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hi.
Goal I am creating a new application for the nRF54l15 and want to follow the latest recommendations for project configuration. I need to do DFU over BLE, so I'm trying...
Hi,
Users of our product have reported issues with multiple versions of Hubitat hubs when pairing Zigbee. I'm investigating this issue and have reached a point where I could...
I want to expand the flash allocated to mcuboot on the NRF desktop, but it failed to start after compilation
The following is a flash layout that can be successfully launched...
Hi,
We have deployed some devices now, and we see quite some modem faults popping up.
Could you try to give all info on what you know about these faults we have from...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
As title.
In nRF54L15 DK, I set "SB_CONFIG_BOOTLOADER_MCUBOOT=y" in file "sysbuild.conf".
It makes main function GPIO toggle stop.
Do have any solution to prevent...
Hi,
I am developing a custom PCB based on the nRF52840 and am currently trying to flash/debug it using an nRF52840-DK (PCA10056) as an external debugger.
connected devices...
Hello all !
Summary
While in power save the nRF7002 RPU powers down its receiver without sending a PM=1 (Null) frame first, so from the AP point of view the station...
Dear Nordic team,
we are evaluating the nRF9151 for a data acquisition application/device. Our first goal was to get the official HTTPS client sample to run on the nRF9151DK...
Hello,
I work on a zephyr project with updatable MCUBoot and two updatable images. This configuration ends up with an unbootable image. The reason is that the CONFIG_MCUBOOT_MCUBOOT_IMAGE_NUMBER...
Environment
SoC: nRF54LM20 (DK; silicon reports nRF54LM20B ENGB — also reproduces built for the LM20A target)
nRF Connect SDK: v3.3.0-rc2, west v1.5.0
Bluetooth: SoftDevice...
We are currently experiencing an issue with the nRF7002 that appears to be present when coexistence is enabled: The nRF7002 becomes unresponsive, seemingly at random, multiple...
Title: nRF52840 / OpenThread: how to inject custom IEEE 802.15.4 RX frames into the native receive path?
Hi,
I am working on a test setup around nRF52840, OpenThread,...
We want to measure latency and PER between two OpenThread Nodes exposed to WiFi interference. Multiple Raspberry PIs, which are configured as AP and/or client, simulate flooded...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
