Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
There seems to be a weird delay of around 11 us between each buffer in a spi_buf_set as shown in the red regions in the image below:
The test involves a transfer of 100...
Hello,
I am currently investigating what the use of the Nordic proprietary protocols (ESB, Gazelle) or an own protocol with direct radio access (similiar to nordic-auko...
I have an Adafruit Feather nRF52840 which I'm trying to use to transmit data over a UART serial connection to a Raspberry Pi. The Raspberry Pi is running a Python test script...
I’m working on reducing power consumption on the nRF54L15 and aiming for an idle current of around 3 µA , as shown in Nordic’s documentation.
With the SDK v3.0.1 hello_world...
Using code from the npm13xx_one_button sample, going into ship mode from event_callback ( const struct device * dev , struct gpio_callback * cb , uint32_t pins ) works fine...
Hi, in video "Building ultra-tiny ML models for any wireless SoC with Neuton" on time 35:35, the presenter Danil Zherebtsov, tells about a repository with a python script...
Hello
Im DJ
I'm trying to test BLE sniffer by buying nRF52840 dongle USB. Looking at the guide,
https://www.nordicsemi.com/Products/Development-tools/nrf-sniffer-for...
I'm developing an OpenThread Sleepy End Device (SED) that periodically sends a payload to a CoAP server, including its own MAC address as one of the values. However, I noticed...
Hello,
Goal: We are developing a long-range BLE application using S8 Coded PHY (125 kbps) to operate reliably at extended ranges (RSSI below − 80 dBm ).
Devices...
Is a Zigbee Direct SDK available for Linux which could be used to allow it to act as a Zigbee Virtual Device (ZVD) using Bluetooth LE?
I am particularly interested in the...
Hi,
I have read the PPK2 user guide here https://docs.nordicsemi.com/bundle/ug_ppk2/page/UG/ppk/PPK_user_guide_Intro.html and the nRF 52833 DK here docs.nordicsemi.com/...
Same problem as , which was 3 years ago...
Our app builds fine until we enable MCUboot, when we get the above warning, and being good people we have CONFIG_COMPILER_WARNINGS_AS_ERRORS...
Where can I find expected throughput for coded PHY in real life? The bitrate for S2 is 500 kbps because there are two symbols per bit in respect to 1M PHY. As part of a packet...
Environment: SDK v3.1.1 with a custom board based on the nRF52840.
I wrote a test application that I've been using to verify the hardware on a custom nRF52840 board. I have...
