Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
There seems to be a weird delay of around 11 us between each buffer in a spi_buf_set as shown in the red regions in the image below:
The test involves a transfer of 100...
Hello,
I am currently investigating what the use of the Nordic proprietary protocols (ESB, Gazelle) or an own protocol with direct radio access (similiar to nordic-auko...
I have an Adafruit Feather nRF52840 which I'm trying to use to transmit data over a UART serial connection to a Raspberry Pi. The Raspberry Pi is running a Python test script...
I’m working on reducing power consumption on the nRF54L15 and aiming for an idle current of around 3 µA , as shown in Nordic’s documentation.
With the SDK v3.0.1 hello_world...
Using code from the npm13xx_one_button sample, going into ship mode from event_callback ( const struct device * dev , struct gpio_callback * cb , uint32_t pins ) works fine...
Hi, in video "Building ultra-tiny ML models for any wireless SoC with Neuton" on time 35:35, the presenter Danil Zherebtsov, tells about a repository with a python script...
Hello
Im DJ
I'm trying to test BLE sniffer by buying nRF52840 dongle USB. Looking at the guide,
https://www.nordicsemi.com/Products/Development-tools/nrf-sniffer-for...
I'm developing an OpenThread Sleepy End Device (SED) that periodically sends a payload to a CoAP server, including its own MAC address as one of the values. However, I noticed...
Hello,
Goal: We are developing a long-range BLE application using S8 Coded PHY (125 kbps) to operate reliably at extended ranges (RSSI below − 80 dBm ).
Devices...
Is a Zigbee Direct SDK available for Linux which could be used to allow it to act as a Zigbee Virtual Device (ZVD) using Bluetooth LE?
I am particularly interested in the...
Hi,
I have read the PPK2 user guide here https://docs.nordicsemi.com/bundle/ug_ppk2/page/UG/ppk/PPK_user_guide_Intro.html and the nRF 52833 DK here docs.nordicsemi.com/...
Same problem as , which was 3 years ago...
Our app builds fine until we enable MCUboot, when we get the above warning, and being good people we have CONFIG_COMPILER_WARNINGS_AS_ERRORS...
Where can I find expected throughput for coded PHY in real life? The bitrate for S2 is 500 kbps because there are two symbols per bit in respect to 1M PHY. As part of a packet...
Environment: SDK v3.1.1 with a custom board based on the nRF52840.
I wrote a test application that I've been using to verify the hardware on a custom nRF52840 board. I have...
