Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
Hi,
I am using an nRF54L15 and I would like to explicitly enable the HFCLK (32MHz). I want to use it to drive TIMER00, which will run during the whole application runtime...
Hi,
I am now developing a production programmer and I want to know the behavior of SWD and SCK lines when the nRF52840 is in RESET state.
Cheers,
Kaushalya
we are using nPM1300 EVK board for an upcoming project we are trying to interface PMIC PM1300 chip with Ambient Scientific processor GPx10 Pro.
It will be a huge setback...
Hi guys, I have been working with a custom PCB based around the nRF5340 that uses the nPM1100 as the PMIC. I have configured it for 1V8 VOUTB output, fixed VBUS, VTERM high...
Hi
Currently I'm evaluating the nRF54L15 die temperature sensor. I’ve taken a few measurements and noticed something I don’t quite understand yet. Perhaps someone could...
We are planning to use the nRF54L15 for a Matter over Thread product, so we are currently evaluating the low-power performance of this device.
According to the nRF54L15...
We are using a BM833 chip on out PCB. There, we may or may not (config-dependant) interact with a sensor via I2C. We observed (statistically), that using the I2C communication...
I am testing an Auracast setup with a Samsung Galaxy A54 5G and Galaxy Buds2 Pro , where my goal is to broadcast two streams with different languages and select either one...
I want to use a new source LF clock to raise the precision from +-250ppm to around +-20ppm. I already have an oscillator mounted in my PCB, so I want to use it for BLE. I...
Hello, my name is William. I made new Lenovo wireless keyboard dongle firmware using nrf52820 and wrote it to dongle. But at first I connected device using J-link version9...
Hello,
I attempted to rebuild the reference circuitry from the nPM2100, and I am measuring unusual power consumption using the PK2 outputting 1000mV.
Partially, I...
I'm using the MCUmgr + MCUboot solution for BLE OTA FW updates (i.e. CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU).
Is there any way to require pairing for firmware updates? I see...
In the LTE_MODE_PREFERENCE Kconfig description the CONFIG_LTE_MODE_PREFERENCE_LTE_M_PLMN_PRIO option states that: " LTE-M, PLMN prioritized
LTE-M is preferred, but PLMN...
Platform: nRF54LM20A SDK Version: nRF Connect SDK v3.3.1 MCUboot Version: Included in NCS v3.3.1
Background
On the nRF54H20 , the IronSide Secure Enclave provides a...
