Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I would like to estimate the current consumption when the controller is advertising at 2.3Seconds, using external crystal, Tx power of 8dBm, Tx payload of 31 bytes. When I...
We are facing in BLE connection issue in Android phone.
we are planning to use 1. Android phone with 'nRF Connect' for mobile as BLE central. 2. Long range demo applictaion...
Hello.
I am currently testing nRF Cloud and encountering an issue.
I have flashed the Peripheral Memfault Diagnostic Service (MDS) sample program to an nRF54L15DK and...
hi,
i build and flash this exercise on nrf9160 DK. everything works okay and the led1,2,3 are turned on and the message is showing me on serial terminal but when i press...
Wireshark Version 4.6.2 nrf_sniffer_for_bluetooth_le_4.1.1
I am trying to capture packets from a long BLE session using Wireshark and the nRF52840 BLE sniffer. Most times...
I am evaluating the nRF54L15 for an power sensitive application and are measuring power consumption on the BL54L15u evaluation module.
However, my measured current values...
Good day,
I am currently using NCS V3.1.1 and nrf52840 devices.
We are making use of the light control server model and a ambient lux sensor device.
I do have the following...
Hi, I would like to use TCXO as main source for HFCLK on my nRF54L15, but not sure if it will work. Please are there any specific steps I need to follow to do and how should...
Hi,
I am currently evaluating the nRF54L15 DFU single-slot sample available in NCS 3.2.1: https://github.com/nrfconnect/sdk-nrf/tree/v3.2.1/samples/dfu/single_slot
I have...
Hi Everyone,
I use Zephyr from nRF Connect SDK and I am trying to build a tf-m sample application (zephyr/samples/tfm_integration/psa_protected_storage) for non-Nordic targets...
Hi Team,
I use your nRF Cloud REST API /location/ground-fix endpoint to obtain location based on LTE cells.
According to your documentation, the „eci” parameter for...
Hello, I am evaluating the device for a new products line and trying to avoid a potential conflicts while mapping I/O's and peripherals for connections on PCB. Where I can...
I have v3.0.0 SDK currently . I am using nrf54L15DK . Do we have any sample code for checking AOA and AOD of the advertisements from the peripheral devices.
I could find...
