Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello everyone, trying NRF for the first time and so far it's been only bunch of frustration and wasted time.
What I need to create is a subset of BM applications for NRF54L...
I am currently developing a HID device that supports BLE and USB. I have tested the firmware update function via both BLE and USB (USB CDC ACM). However, I am experiencing...
We aim to use an external Cellular module for MQTT communication.
I found that the nrfxlib/nrf_modem library is only supported for nRF9x series MCUs. Does this support...
Hi all, I'm trying to enable the SPIM4 peripheral on the dedicated high-speed pins (P0.08 SCK, P0.09 MISO, P0.10 MOSI, P0.11 CS) on the nRF5340DK, but I'm seeing no activity...
Been trying to set up a project to run some basic openthread as a proof of concept project. I based much of it off the CLI example and SDK. I have gotten stuck where my code...
Hi, I am using BMD-350-A-R module for a project and i am trying to upload the bootloader and the bootloader settings hex files but those are getting written as application...
Hi,
I am working with a u-blox EVK-NORA- B206 development kit. It has an onboard J-Link and it contains a NORA-B206-00B which has a NRF54L15 inside. I use VS Code with the...
Hi,
Could you provide some examples demonstrating how to use the FLPR on the nRF54L15 with NCS 3.2.1?
Additionally, real-world use case examples would be appreciated,...
Hello,
I am following this course: https://academy.nordicsemi.com/courses/bluetooth-low-energy-fundamentals/lessons/lesson-3-bluetooth-le-connections/topic/blefund-lesson...
Hello,
Developing a new pcb with combined nRF9160, nRF5340 and nRF7000. We want to power the system with a nPM1300 PMIC. nRF9160_VDD on VSYS(4.5V), nRF9160_VDD_GPIO on VOUT2...
The Matter Samples output a verbose level of information to the console as standard. This is a mixture of the application log statements and matter log information. When trying...
Hello,
I am writing to ask a question regarding the power supply configuration when using an external board with the nRF5340DK.
I am referring to page 30 of the nRF5340DK...
Hi all
I have following problem. When using ble_nus_c_string_send to send data over NUS sd_ble_gattc_write returns error 19 - NRF_ERROR_RESOURCES after but the problem is...
Hi Nordicsemi engineers,
While testing a large-scale OpenThread network recently, I encountered an irregular pattern of device crashes. The network consists of 70 devices...
