Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hi,
I am working on a project with channel sounding requirements and I have collected some test data. I am using the example codes Bluetooth: Channel Sounding Initiator...
I am developing an application using nRF52833 + nRF5 SDK + S140, and I encountered a strange issue. When I perform an OTA update from a firmware that does not initialize the...
Hi there,
I am using MDBT dev kit based on MDBT53-1M module. I have a simple application of reading an SD card and printing the data on the LOG. While the current application...
Hi
for DFU is bluetooth used by default. Your DFU app suports only using bluetooth to do a DFU.
Do you have any tools to do a DFU over NFC? Or do I have to write a tool...
## Summary
When running the OpenThread CLI sample on `nrf54lm20dk/nrf54lm20a/cpuapp` using nRF Connect SDK v3.2.4, the application crashes immediately on boot with a ...
Reporting this here as the project GitHub asked that bugs be reported via DevZone.
The latest Power Profiler v4.2.0 has introduced an annoying issue - when running the Power...
I have an application that gets a fix using A-GNSS. I couldnt understand from the documentation how to enable other satellite systems other then GPS to be enalbled in my application...
Hello,
I am trying to run this Android-nRF-Blinky sample from Git ( https://github.com/NordicSemiconductor/Android-nRF-Blinky ) and build failed.
Below is the error message...
I make a BLE/USB MIDI controller that has an NRF52840 receiving sensor data by SPI from an Atmega 32u4 at 2Mhz. The NRF52840 is the SPI master (SPIM3). When I'm using BLE...
Hi there, I am using nrf connect sdk v2.6.0. I have noticed that after DFU update, I am seeing ble bonding lost randomly on firmware side. I did uncheck Erase Application...
We are running some sample code on the nrf54l15 mcu, specifically: /modules/lib/memfault-firmware-sdk/examples/nrf-connect-sdk/nrf5/memfault_demo_app
We can connect and...
Hi nRF support team,
I am evaluating ST7735 LCD with the nRF82540 development kit. For your information, I am able to set-up the nRF Connect SDK environment on nRF82540...
Hi Sir, I am developing with the nRF52840.
I installed nRFConnect 5.2.1 and the programmer (version 4.6.2), Following the programmer’s prompts, I installed SEGGER J-Link...
SDK version: 3.2.4
I am using two nRF5340 Audio DK boards configured as gateway and left headset.
I added " CONFIG_STREAM_BIDIRECTIONAL =y" to prj.conf and I built everything...
Hello,
I am working with the nRF54L05 and testing SAADC inputs.
I observed the following behavior:
AIN4–AIN7 work correctly as ADC inputs
AIN0–AIN2 show unstable...
