Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi all
Im trying to implement on bluetooth communication between two nrf52840 DK, I have made a custom uuid service on peripherial. Now I have to do GATT discovery service...
Hello! We are developing a schematic for our device and trying to correctly assign GPIOs for different peripherals. There is the Cross power-domain use section in the documentation...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hello at all, I try to compile the example peripheral_uart for the nrf54L15-DK. The goal is to compile without west. My directory structure:
where I copied everything from...
Hello,
I am developing on the NRF54L15 DK board, using the SDK v3.1.0 and v3.1.0 toolchain. I am trying to use the macro NRF_RADIO_INT_RSSIEND_MASK, but RADIO_INTENSET_RSSIEND_Msk...
I'm using the NRF5340. When I open a standard example project located in the directory: nrf\samples\bluetooth\peripheral_uart (the well-known Bluetooth data transparent transmission...
I am experiencing system resets caused by the WDT (Watchdog Timer) while using the nrf52832。
This is my WDT configuration code：
void system_wdt_init(void) { uint32_t err_code...
my sdkconfig.h related to fds
my entire code error: my entire sdkconfig
i have tried changing no of pages , using nvmc driver, but i am getting the same error steps...
HI，
I am using the nRF54L15 with SDK v3.0.0. I am currently using Timer20 for a counting function. My original power consumption was 4.6 μA when Timer20 was not enabled...
Dear Nordic DevZone,
I have a question which is quite noobish but I want to make sure I am using the right tools for the job. My setup looks like this I have a raspberry...
After gradually increasing up to ncs 3.1.0, the following issue occured: After:
LOG_INF ( "Initializing modem library" );
err = nrf_modem_lib_init ();
if ( err ) ...
Hi [Nordic Support Team / Developer Team],
I would like to confirm why the nRF54L15DK is not listed among the supported development kits for the Bluetooth: Peripheral ANCS...
I tried two different applications in BT fundamentals, the solution to Lesson 3, Exercise 1 and the solution to Lesson 4, Exercise 1. Both show "Advertising successfully started...
I'm using zephyr with a custom board (nrf52840) which has a ssd1306 OLED. I have it configured to use i2c0 and is working fine with lvgl.
When I try to enable uart0 (using...
After a recent update, I'm frequently finding the VS Code UI unresponsive due to intelliscan re-indexing.
About my setup. I have a complex environment with 4 different...
