Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hello
since i could not post a ticket (got the message 'could not create a ticket'), I try it again with almost no text here but added the content in a txt-file.
Hope...
Dear Nordic-Team,
we are currently trying to add CSR creation to our project which worked quite fine by implementing it similar to the psa_crypto sample.
Unfortunately...
Hello Nordic Team, We are developing a wearable health device using the nRF5340-DK and Zephyr RTOS. As part of the BLE communication design, we intend to use **Security Level...
I am looking at options to integrate the ADXL 367 accelerometer into my firmware project (nRF Connect SDK 3.0.2). I see the sensor is supported by Zephyr and has a complex...
We are hardware manufacturing company currently developing AMI solutions with Wirepas integration. Do any of your partners offer smart meter solutions that use Wirepas and...
Before i inserted in my code to use ppi + gpiote + spim usb serial device port worked properly, it connected normally, but now it doesn't connect the port at all, did i create...
Hello, I am working on a custom board with my own custom project/application. I have recently done porting from ncs v2.7.0 to v3.0.2 - I was able to initialise the wifi driver...
Hi Nordic team,
I'm currently working on a real-time distance measurement project using channel sounding with the nRF54L15 DKs. I’ve been using the channel_sounding_ras_initiator...
Dear Team,
I would like to know if it is possible to add custom attributes and commands to standard clusters, such as the Occupancy cluster. I have reviewed the "Adding...
Hi everyone—I'm working with the Nordic nRF54L15 SoC , but I'm struggling to find guidance on using a chip antenna (design and components) . The official materials (e.g.,...
Hi Team,
I’m facing an issue when trying to perform BLE FOTA with a 2 MB external SPI flash (SPI4) as the secondary slot for MCUboot.
My setup works fine when using a...
Hello,
sorry, do not know where to file a bug.
Bug is, that nrf_radio_subscribe_get() and nrf_radio_publish_get() use the wrong offset (0x80) instead of the correct one...
Hi, I’m currently testing the update process via BT SMP on the matter window covering example (NCS 3.0.2, nrf5340). For my test, I created two versions: 1. Project with -DCONFIG_CHIP_DFU_OVER_BT_SMP...
Dear reader,
I am currently working on a project using the NRF54L15 MCU. There is plenty of documentation available for this component, and the reference circuitry for the...
