Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hi there,
I am seeing inconsistencies with the PCB layout specification of the nrf7002.
1) In the v1.1 of nrf7002 datasheet, it is recommended that the following capacitors...
Hello, we are currently testing the output of square waves through GPIO output pins. However, I found that a single operation to set the GPIO output pin high or low using...
I've installed the same version of the Power Profiler V4.3.1 on Linux and on windows.
On windows the device gets recognized straight away and I can use it, on Linux however...
If I understand correctly, you can pretty much assign any pin to any peripheral. I've been using a modded central uart project on a dev board but on this other board I'm using...
Hello,
is there any way to access the Stack and Heap Start/End memory addresses from the zephyr code?
I have found the __INITIAL_SP definition that gives the Stack start...
Hi,
I have been working through the Dev Academy cellular course using the nRF9151 DK which is fitted with a 1NCE MFF2 eSIM. I was able to set this up in the Board Configurator...
Hello Team,
I am using the nRF52833 with the nRF Connect SDK (v2.9.1) in VS Code , and I am experiencing an issue with the RTC calendar update.
I initially set the RTC...
Hi everyone,
After a debugging session using the debug tool in nRF Connect SDK with an nRF52832 on a custom board, the chip is now completely unresponsive—I can't flash...
Hi, Recently we upgraded to nrf-sdk 2.7.0 (previously on 2.6.1) and I began to notice that NFC had stopped working for our project, when running on nrf5340dk.
While switching...
To preface:
Board: nRF9151DK
nRF Connect SDK / Toolchain: 3.1.0
Hello,
I am attempting to learn and integrate full modem FOTA functionality into my application...
Bonjour,
We are working on a firmware upgrade for our product based on a nRF52833.
With the previous firmware, compiled with SDK 2.3.0, when the board was OFF, the power...
HI
I am using the NCS 3.0.0 SDK and want to use FCB to store sensor data only in external flash.
Therefore, I added external flash to the pm_static.yaml file in the project...
I’m using the nRF9151-DK Evaluation Board . Normally, I connect the board to PC via USB — for programming/debugging
However, since I’m preparing for production testing,...
