As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hello,
I am evalating the nRF9151-SMA-DK with a Monogoto SIM card that uses Skylo NTN connectivity.
I am able to reach the internet, since DNS resolution works:
...
Hello,
We are using a custom board based on the nRF5340 + nRF7003 Fanstel module with NCS SDK v2.6.2.
Our application uses MCUboot with dual-bank OTA updates. The secondary...
Hi,
What file or files should contain CONFIG_GPIO=y for a simple application developed with nRF Connect SDK v2.9.0 such that VS Code does not show squiggles under #include...
Hi,
BLE throughput differs between NCS v2.6.0 and v2.9.2. v2.9.2 appears to have fewer MoreData packets. (Both have CONFIG_BT_CTLR_SDC_MAX_CONN_EVENT_LEN_DEFAULT set to...
Hi, Team:
I want to make an LED blink during OTA upgrade and stop blinking after upgrade.
How do I configure prj.conf, sysbuild.conf, or provide some demos
Thank you...
Hi
I'm encountering a problem than the ANT device cannot be scanned. you can use project "ble_ant_app_hrm_v324"(ncs 324）, and modify "
light_rx_open_head" to connect...
I have discovered a serious issue with Bluetooth connectivity on iOS 26.
My device use nrf52832 and sdk15.3, it consistently disconnects just a few seconds after a successful...
Hello everyone,
I have tried several different approaches to solve this issue, but I have not been successful so far.
My goal is to generate an interrupt when the LIS2MDL...
Hi,
We have sent out our product (includes the nRF9160 SiP and an nRF52840) for EMC testing and the test lab is asking for the following:
nRF9160 LTE Cat M1 and NB...
We have noticed an issue with our device built on nRF5 SDK + nRF52832 when connected to iOS 26.
Initially after connection, everything is ok. Then we attempt a connection...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
Hello Nordic Team,
I am designing a custom PCB using the nRF52840 and a PCB trace antenna for 2.4 GHz BLE.
In my current design:
I will take nRF52840 dongle antenna...
I am using the nRF5 SDK, nRF52833, and nRF52832.
I flashed the following two demos:
nRF5_SDK_17.1.0_ddde560\examples\ble_central\ble_app_uart_c\pca10100\s122 (nRF52833...
Hello,
We are currently developing a Zigbee product using nRF Connect SDK v2.8.0 . While reviewing the release notes for NCS v2.9.0 , we noticed two critical bug fixes related...
