Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
I'm using the peripheral_bms project. The only change being in the overlay to make it work with nrf52833 dk. I'm able to connect with nrfConnect and see the services (except...
I'm developing with the NRF52840 using IAR Embedded Workbench , and implementing wireless communication based on the IEEE802.15.4 Zigbee protocol .
In the MAC frame layer...
I am new to Nordic and want to design with the nRF52840. I have read this guide:
used AppCAD to find the best width and clearance for the ground layer, but when I downloaded...
Hello, I am using NCS 3.0.2 on nRF52840. I have been using MCUBoot for a long time on my device, and it is working fine. Recently, I went through a requirement where I needed...
Hey everyone,
I've been trying to get the Bluetooth Mesh DFU Target sample working on my nRF5340 DK and running into some issues. I've read through the docs.nordicsemi.com...
Hi All,
I have an nRF5340 Audio DK which has problem with the network core. When I connect the USB to board or try to recover the board the MCU light at the bottom of...
Hello all,
I am working on a project with 2 nrf5340 Audio DK's and I want to have the same functionality of the walkie talkie demo but instead use the microphone of the...
I had a working Matter application, but due to some human error, I erased my WSL installation.
I set it up again, but after successfully flashing my code onto the Nordic...
Hi,
For a product currently under development, we need to use a counter as an RTC. We’re targeting the following commit in ncs/sdk-zephyr :
github.com/.../d7e41fd2e361ee15454a253ebec9bb37aceaf09f...
Hello Support Team,
I am currently testing the new Channel Sounding feature on two nRF54L15 boards, on which I flashed your Channel Sounding samples ( initiator and reflector...
Content: I’m working on integrating the nRF7002 EK over SPI with an nRF54L15 using nRF Connect SDK v3.1.1 . While setting up the workspace, I noticed that the Wi-Fi driver...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
I used the nRF Audio Example to build a BLE audio device. I use the test tone generator functionality. I was previously using nRF Connect SDK 2.6.1 and the test tone generation...
I am an FAE with Ezurio, we have a customer who was running through the nRF Connect SDK Intermediate training on DevAcademy and they ran into issues with AuTerm in Lesson...
## Description
On the nRF54L15DK, the measured floor current increases significantly when the GPIO is configured for button edge detection.
### Observed Behavior
* Floor...
