Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
I am currently developing a HID device that supports BLE and USB. I have tested the firmware update function via both BLE and USB (USB CDC ACM). However, I am experiencing...
We aim to use an external Cellular module for MQTT communication.
I found that the nrfxlib/nrf_modem library is only supported for nRF9x series MCUs. Does this support...
Hi all, I'm trying to enable the SPIM4 peripheral on the dedicated high-speed pins (P0.08 SCK, P0.09 MISO, P0.10 MOSI, P0.11 CS) on the nRF5340DK, but I'm seeing no activity...
Been trying to set up a project to run some basic openthread as a proof of concept project. I based much of it off the CLI example and SDK. I have gotten stuck where my code...
Hi, I am using BMD-350-A-R module for a project and i am trying to upload the bootloader and the bootloader settings hex files but those are getting written as application...
Hi,
I am working with a u-blox EVK-NORA- B206 development kit. It has an onboard J-Link and it contains a NORA-B206-00B which has a NRF54L15 inside. I use VS Code with the...
Hi,
Could you provide some examples demonstrating how to use the FLPR on the nRF54L15 with NCS 3.2.1?
Additionally, real-world use case examples would be appreciated,...
Hello,
I am following this course: https://academy.nordicsemi.com/courses/bluetooth-low-energy-fundamentals/lessons/lesson-3-bluetooth-le-connections/topic/blefund-lesson...
Hello,
Developing a new pcb with combined nRF9160, nRF5340 and nRF7000. We want to power the system with a nPM1300 PMIC. nRF9160_VDD on VSYS(4.5V), nRF9160_VDD_GPIO on VOUT2...
The Matter Samples output a verbose level of information to the console as standard. This is a mixture of the application log statements and matter log information. When trying...
Hello,
I am writing to ask a question regarding the power supply configuration when using an external board with the nRF5340DK.
I am referring to page 30 of the nRF5340DK...
Hi all
I have following problem. When using ble_nus_c_string_send to send data over NUS sd_ble_gattc_write returns error 19 - NRF_ERROR_RESOURCES after but the problem is...
Hi Nordicsemi engineers,
While testing a large-scale OpenThread network recently, I encountered an irregular pattern of device crashes. The network consists of 70 devices...
Hi,
I am working with NRF54L05 SoC using NRF Connect SDK V3.1.0 and NRF54L15DK for testing.
I am seeing an inconsistent MCUboot validation failure when flashing a firmware...
