I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello.
I'm trying to use WS2812 leds with I2S. I'm using two boards for testing: an NRF5340DK and my board based on the HOLYIOT-21069-5340 module.
I'm using a zephyr/samples...
using ncs 3.1.1 how can we invert SW_CTRL0 logic we using a different RF SWITCH then DK
"Does register 0xA4002DC8 (SLEEP_CTRL_GPIO_CTRL) on nRF7002 have a bit to invert...
nRF5340-DK, PCA10095, v2.0.1 and v2.0.2
According the zephyr device tree, the UART0 is mapped to GPIO 0.19/0.20 and UART1 is mapped to GPIO 1.0/1.1 .
According the schematics...
Dear Nordic,
I got some AT commands here <https://docs.nordicsemi.com/bundle/ref_at_commands_nrf91x1/page/REF/at_commands/production_test/xrftest_tx_set.html> to know that...
Hello Nordic Team,
I am currently working on OTA using Sysbuild configuration on the nRF52833 with the nRF Connect SDK .
In this configuration, I enabled overwrite-only...
I'd really like to be able to set the path to nrfuitl in the extension so I do not have to put int on my system path, but rather keep it contained in my project.
Use Case: We are developing a Bluetooth Mesh people-counter on the nRF52840 DK .
Primary: Mesh network for publishing/receiving sensor data.
Secondary: Custom...
Hi,
it seams, that MBED DTLS implementation in nRF9160 firmware v1.3.1 is not compiled with Extended Master Secret Extension https://datatracker.ietf.org/doc/html/rfc7627...
Hi,
Is NTN available on nrf9151 A0A version silicon?
I am struggling to get our device configured for NTN communications with SatelIot and Skylo.
Does the version...
I'm trying to establish an SPI connection, but I'm not getting any signal when measuring the pins with an oscilloscope. This is my devicetree;
& spi00 {
compatible ...
I am creating a bluetooth mesh using nrf54L15 and would like to make use of public key OOB as a means of whitelisting devices (so only my devices can join the mesh). The idea...
Hi everyone,
I'm trying to generate SBOM from the code based on nRF SDK v17.1.0. I noticed that SBOM feature was only supported with NRF Connect SDK. I did search for...
Hi, I have been having some trouble lately using an SD card together with a LoRa radio. I am using separate SPI instances for LoRa and the SD card (SPI1 and SPI2). However...
