I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi, I want to change the voltage of the VDDIO in the group of pins labelled Port 1. I launched Board Configurator from nRF Connect for Desktop but it says "This development...
I have code set up to configure Timer3 to generate a Compare event at 100 KHz, using the PPI so that triggers an ADC Sample event for the two enabled ADC channels. EasyDMA...
I have been testing the thingy91x and measuring power consumption trying to reduce it to the absolute minimum.
Using a test program that moslty sleeps ( using k_sleep()...
Hi,
I'm developing an application with a custom firmware image for both the nRF52840 and nRF9160 on the nRF9160DK. I've always been on ncs v2.5.0 and decided it would...
Hello,
I am trying to program a custom device of nrf54l15 using nrf connect for desktop app(V5.2.0) -> Programmer(V4.6.2)
I am able to program it but this is how I see...
I am bringing up a custom board using the nRF54L15 (Fanstel BM15M module) and I am using SPIM00 as the high-speed SPI interface. I am configuring the peripheral through Zephyr...
Using PPK to measure the current, it was found that there was a 1-minute cycle signal in the current waveform. No timer was set. The watchdog timer is 10 seconds.
Im currently working on a project which should receive audio through CIS and retransmit it over BIS. Im using nrf5340_audio_dk for this. Ive tried using https://docs.nordicsemi...
Hi,
We came across this feature " PLMN selection optimization during initial search ", enabled by AT%FEACONF=0,3,1 . It sounds good for speed and power consumption.
...
Hi all,
I’m working on a custom board based on the nRF9151 , and using the Ignion NN03‑320 antenna for GNSS reception.
In our GNSS TTFF testing (using AT commands),...
I'm developing a keyless entry/start system for vehicles with the following requirements:
The vehicle side uses an nRF54L15, while the mobile phone is a standard smartphone...
Hi,
I am developing an audio application on nRF54L15. I have successfully used the Zephyr API to read sequences from the ADC with extra samplings (the "extra samplings"...
Recently I noticed (for reference in the NCS/v3.1.1 SDK) that some nrf9151 boards are in zephyr folder structure and others are in the nrf folder structure.
NRF9151DK...
Hi support:
When testing the peripheral nfc pairing sample on the nRF54L15-DK development board, and using an Android phone for testing, it was found that...
