Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
currently this is more of a theoretical question, but i have an idea of something that might utilize this (3 QSPI devices)
Ive been looking at the Nrf5340 and the nrf7002...
Hi, I am stuck on the BLE channel sounding Initiator initialization. I took the code from the channel sounding connected initiator and integrated into my FW.
Due to unknown...
Hello Nordic Team,
I am using the nRF5340 Audio DK and I want to implement a simple audio loopback — where the board captures voice from the on-board PDM microphone and...
hello~
nPM1304 nominal sleep mode 500nA (it is still uncertain whether the buck converter can operate?)
Can't the sleep mode be lower than 500nA?
best regards
sam
I'm following the Lesson 9, Exercise 2: DFU over USB - Adding External Flash from the Nordic Academy: Tutorial Link
SoC: nrf54l15
SDK version: 3.0.2
Toolchain version...
Hi,
I’m using a custom nRF5340 board , and I recently migrated my project from nRF Connect SDK v2.9.0 to v3.1.1 .
The same project compiled and worked fine on v2.9.0,...
Hello,
I'm interested in nRF54L10 SoC, in Mouser and DigiKey I see that I can buy it in this package: QFN48 (QFAA). However in the datasheet it shows this package QFN40...
Hi,
I’m currently working with the nRF54L15 DK using the Channel Sounding Initiator with Ranging Requestor sample from the latest nRF Connect SDK. The setup runs successfully...
Dear nRF experts.
I am using the radio_test sample with SDK3.10
We used radio_test to add UART commands to control the on/off of all GPIOs for pin verification. We found...
I'm currently looking for a high-speed data transmission and reception solution that requires wifi (NRF7002) throughput, but I don't want to transmit data via wifi. It should...
I'm using nRF Connect for Visual Studio Code, working on a project that has worked great in the past, but I'm getting error messages now when attempting to flash any board...
Hi,
We are using the PMIC in our smart ring where we have limitations of number of components used and specially the height of the components used. Here, the inductor...
Dear Nordic Support Team,
Hope this email finds you well. I am currently developing a Matter-enabled device using the Nordic nRF Connect SDK, and I’ve encountered a question...
Hi,
I just got a power profiler kit II and I want to use it in an battery based application, where there is also the possibility that current will flow in the opposite direction...
