Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hi, So, I want to do BLE DFU from one nRF52 MCU to another nRF52 MCU. The start point for me was this:
put SMP server sample on one nrf52dk (this device is advertising...
Hi
I am using the ESB sample and want to use the RADIO_MODE_MODE_Nrf_250Kbit PHY, but I will get not support after requiring:
Can we still use 250 PHY in nRF54L15 ESB...
Hi,
After upgrading from NCS 2.5.2 to NCS 3.1.1, I get quite frequent MPSL assertion errors on a nRF52840. Can you shed some light into what this assertion error is about...
The datasheet list
A25, B12, B26, D2, F2, G1, H2, J31, K2, T2, AG31, as N.C.
I have not been able to read exactly what N.C. implies: It could be: "do not connect", "no...
Hello,
I am working a project that uses the NRF52840 dongle with BLE and UART to communicate to two separate devices while going through temperature cycles. I have not...
My device supports both Central and Peripheral roles. By default, it works in Peripheral mode. When the device connects in Peripheral mode, I want the following behavior:...
Hello Nordic team,
I am working on an nRF52840 project using nRF Connect SDK (Zephyr-based, v2.x / v3.x) and I would like to clarify the official support status of a specific...
Running doxygen nrfx.doxyfile
Per the README.md in C:\ncs\nrf-bm\v1.0.0\modules\hal\nordic\nrfx\doc fails.
See output below.
C:\> C:\apps\doxygen-1.16.1.windows.x64...
Hi there.
we have firmware that was running on nRF5340 MCU. we had decided to migrate to the nRF54H20 MCU because of flash size limitation. this MCU was announced with 2MB...
I am trying to connect to two reflectors and sound only from 1 device so far the connection and soundnig works well for first set of connection and after a disconnectio, the...
I am modifying the Qorvo UWB SDK to add BLE operations. I have posted a couple other topics about different issues..
I have ported my code to the latest Qorvo SDK, They...
With NCS 3.0 and the nRF54L15, even after applying patches, the power consumption anomaly can still be reproduced at the edge of the NFC range. The power consumption anomaly...
We are using zephyr's conn_mgr to manage the network connection. From what I can tell, if I have set CONFIG_NRF_MODEM_NET_IF=y and NRF_MODEM_LIB_NET_IF_CONNECTION__PERSISTENCE...
I want to try the tdm function on the nrf54lm20 dk.
But i have encountered problem in the first step.
I do not know how to add the tdm port and assign the pin.
Whin...
Hi.
We are using nRF Connect SDK v3.2.1 and nRF52832 MCU.
Our current internal flash memory mapping is like below,
mcuboot + mcuboot_primary (application) + mcuboot_secondary...
