I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Heads up for anyone using the IoT SDK (currently 0.8.0). This SDK has the TinyDTLS-0.8.1 embedded in it... and I believe that there is a bug in the TinyDTLS CCM functions...
Hello,
Are there any samples that show multi-core (sysbuild) configurations for the nRF54H20?
I've found the sysbuild HelloWorld project, but in the sysbuild.cmake file...
Hi
We have just been notified by our supplier that they have detected som anomalies when taking X-ray images after soldering our 208 pcb's. they estimate around 25% will...
Hi, I appreciate some help with my situation. Here's my setup.
nRF54L15-DK using nRF Connect SDK 3.1.0 .
using nRF52840 dongle as proxy for BLE
nRF Connect for Windows...
I am using nrf54l15 with NCS v3.1.0 with the following error when i connect it(i worked in NCS v2.9.1 successfully):
Controller unresponsive, command opcode 0x2035 timeout...
Recently, we decided we would try ESB, since the power consumption is similar to BLE, but the intervals are much shorter, and we could greatly benefit from this.
I've seen...
I am migrating a project to Sysbuild where we previously were doing some post-build steps that require access to PM variables like PM_MCUBOOT_PRIMARY_SIZE.
Previously, we...
Hello, I've been trying to get MCUboot running on my custom board with the nRF9160 for two days now, and I'm honestly at my wit's end. The main application is written and...
Hello,
we are testing BLE MESH vs THREAD to build a home automation network.
We understood that WiFi interference is a real concern in this application. In fact, we...
Hi,Team,
I'm currently using the nrf54l15-dk. I want to set the rtc of the nrf54l15-dk to obtain the timestamp. How should I configure the timestamp ? Which examples should...
First, I can use I2C with SCL on pin P1.11 and SDA on P1.12 with NRF54L15DK.
But then, when I try to change SCL to P0.03 and SDA to P0.02. I2C does not work anymore.
The...
SDK: nRF Connect SDK v3.0.2
DK: nRF54L15-DK
Sample: spi_flash
default:
mspi-max-frequency = < DT_FREQ_M ( 8 )>;
If I change it to 32, it will printf these...
Hi am trying to use Nrf54l15 as a controller with an external host for the Channel sounding feature. I can receive CS subevents from the NRF controller, but the same thing...
I am using a QFN73 pin package of nRF52840. The data sheet says it has built in balun. So if I follow the reference circuit, where do I see 50 ohm looking int to the chip...
having just seen the announcment about the bare-metal SDK, i gave it a try using my "hello world" of BLE -- a minimal beacon app which i actually use to benchmark BLE platforms...
Hi
I am capturing a digital signal with the nRF PowerProfiler Kit II from my board that can either be 12Hz or 2kHz depending on the state of my application.
In the below...
