Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
I am testing a custom board prototype and having trouble getting I2C to work.
During testing, I was able to observe activity on the SDA line, although it consisted of only...
Hi,
I am using the heart rate sample.
I have connected ground to ground, 3.3v to vdd, SDA to pin 26 and SCL to pin 27. I have 4.7k pullup resistors on SDA and SCL. When...
Hi Nordic team,
I am opening this new thread as a follow-up to my previous question:
https://devzone.nordicsemi.com/f/nordic-q-a/128246/how-to-reach-datasheet-level-2...
Hello Zephyr Community,
I am trying to contribute a new sensor driver for the **AMS AS7341 Spectral Sensor** to Zephyr (using **NCS v3.2.2 / Zephyr**), and I would appreciate...
Hi Team,
We require the detailed procedure for locking and unlocking JTAG access on the nRF54L15 device . Specifically, we are looking for:
Steps to enable JTAG...
Hi,
I am working on a Zigbee coordinator based on nRF52840 using the nRF5 SDK (ZBOSS stack).
My network includes up to ~50–60 devices (both mains-powered and battery-powered...
Hi,
We had connectivity issues on our end for the Message Routing Service webhook since May 13, 2026. It has been restored and tested with the nRF Cloud verification test...
Title:
Hi,
We want to use the nRF9151 as an external LTE modem , controlled from another MCU through UART AT commands .
We have designed our own PCB with the nRF9151...
Hi Nordic team:
If my product has mesh functionality and needs to pass NLC certification and needs to be tested with a PST tool at a testing agency.
Do I need to flash...
Hello Nordic Support,
We are developing a project using two setsof nRF5340 DK with the nRF7002 EK attached. We are trying to achieve coexistence between Wi-Fi in SoftAP...
Hi,
I am working on integrating the peripheral_uart sample with nRF5340 Audio (LE Audio) on the nRF5340 Audio DK.
Setup
Peripheral Side
Merged applications:
peripheral_uart...
Hello,
I am currently working with nRF52832 and have been referencing the following sample code: nrf52-esb-ccm-example / ptx/main.c
I have successfully implemented AES...
Environment
SoC: nRF54LM20A (cpuapp, non-secure / TF-M)
nRF Connect SDK: v3.3.0
sQSPI soft peripheral driving an AMOLED display via the FLPR
BLE active via MPSL...
Hi team,
Please find below logs. While programing this error occurs. please find the logs and do needful. Earlier programing happens now it's not happened. Based on below...
