Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello, I have used nRF Connect for Desktop with the nRF52840 dongle and it works perfectly as far as using the dongle as a central device and a peripheral device (BLE advertising...
Hi,
I am using an nRF54L15 and I would like to explicitly enable the HFCLK (32MHz). I want to use it to drive TIMER00, which will run during the whole application runtime...
Hi,
I am now developing a production programmer and I want to know the behavior of SWD and SCK lines when the nRF52840 is in RESET state.
Cheers,
Kaushalya
Hi,
Users of our product have reported issues with multiple versions of Hubitat hubs when pairing Zigbee. I'm investigating this issue and have reached a point where I could...
we are using nPM1300 EVK board for an upcoming project we are trying to interface PMIC PM1300 chip with Ambient Scientific processor GPx10 Pro.
It will be a huge setback...
Hi guys, I have been working with a custom PCB based around the nRF5340 that uses the nPM1100 as the PMIC. I have configured it for 1V8 VOUTB output, fixed VBUS, VTERM high...
Hi
Currently I'm evaluating the nRF54L15 die temperature sensor. I’ve taken a few measurements and noticed something I don’t quite understand yet. Perhaps someone could...
We are planning to use the nRF54L15 for a Matter over Thread product, so we are currently evaluating the low-power performance of this device.
According to the nRF54L15...
We are using a BM833 chip on out PCB. There, we may or may not (config-dependant) interact with a sensor via I2C. We observed (statistically), that using the I2C communication...
I am testing an Auracast setup with a Samsung Galaxy A54 5G and Galaxy Buds2 Pro , where my goal is to broadcast two streams with different languages and select either one...
I want to use a new source LF clock to raise the precision from +-250ppm to around +-20ppm. I already have an oscillator mounted in my PCB, so I want to use it for BLE. I...
Hello, my name is William. I made new Lenovo wireless keyboard dongle firmware using nrf52820 and wrote it to dongle. But at first I connected device using J-link version9...
Hello,
I attempted to rebuild the reference circuitry from the nPM2100, and I am measuring unusual power consumption using the PK2 outputting 1000mV.
Partially, I...
I'm using the MCUmgr + MCUboot solution for BLE OTA FW updates (i.e. CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU).
Is there any way to require pairing for firmware updates? I see...
