Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
There are two USB ports. IMCU and nrf5340. I had a lot of trouble with bad cables but i found one that works and I find that I have a jlink drive that pops up so I know there...
Hello, I am trying to convert my codebase from segger embedded studio to nrf connect. I am currently working on the spi section of my codebase.
I am communicating from...
Using SDK 2.4.2
1) Is there a way to specify multiple MCUBoot keys in the same way they can be specified for NSIB? MCU Boot allows an array of keys, but it looks like zephyr...
Hi! Do people actually use the 2.2-4.7Ohm series resistor on the VBUS input to the nRF5340? It's just such a low resistance, I don't particularly see the point. Thanks!
Hi Team,
I am working on OTA using an external Winbond flash IC (W25Q64) with the nRF52832 controller in NCS SDK version 2.9.2. I have completed all the required configurations...
Hi,
I want to set my BLE advertising as public adress Dynamic, and can't work. I have try reboot,, and call "bt_ctlr_set_public_addr" before "bt_enable", It is working first...
I used two development boards with 52840, Two development boards are running 'first' and 'second' in the '\examples\802_15_4\wireless_uart\secure', respectively.
Additionally...
Hi All, In the NRF54L15 SoC, the main ARM core and the co-processor RISC core share the same set of peripherals even though both the cores can have separate sections of RAM...
Hello
I need some advice on FOTA via BLE on the nRF54LM20B. I use SDK v 3.3.0, building /ns variant.
I managed to get FOTA working to upload an updated image via BLE,...
Hello everyone, I have a question regarding the LIS2MDL sensor. When I configure Register A, it correctly takes the value that I set. However, after the sensor initialization...
Dear Nordic Team,
We are working with the nRF52833 using nRF5 SDK 17.1.0 and have implemented OTA DFU in our application.in OTA We have merged all firmware components...
Hi,
After installing nrf sdk v2.9.3 trying to build application under Windows fails with the following message:
Trying to run any command inside the NCS shell/terminal...
Hello, We are building an application with NRF54 as the host MCU and NRF9151 as a serial modem. We are considering using a SoftSIM from Monogoto. Our main concern is how easy...
Hello everyone, I have a question regarding the LIS2MDL sensor. When I configure Register A, it correctly takes the value that I set. However, after the sensor initialization...
