Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
I have and nrf5340 connected to debian system via uart. I'm trying todo a flash update via the uart and the nrf5340 is unresponsive. The MCUmgr is not getting any response...
Hi there,
I'm using /opt/nordic/ncs/v3.3.0/zephyr/samples/bluetooth/channel_sounding/connected_cs/initiator and /opt/nordic/ncs/v3.3.0/zephyr/samples/bluetooth/channel_sounding...
Issue
How to properly wake an nRF54L15 from System-Off mode when the device receives a UART transmission, without the use of the LPUART Ready and Request lines or any sort...
Board: nRF52840 DK (pca10056) NCS version: v3.2.3 Goal: Send and receive raw 802.15.4 frames with a custom packet format, without using OpenThread, Zigbee, or any other mesh...
When attempting to install a downloadable app in nRF Connect for Desktop 5.3.0 on Linux, the installation fails with an EISDIR: illegal operation on a directory error. The...
As mentioned in subject,I try to study course with CMSIS-DAP,now, chip recove and flash is OK,but blocked at debug step for 2 days now.
Maybe I made some wrong config some...
In nRF cloud, in the device list ( https://app.nrfcloud.com/#/devices ) it is difficult to manage larger number of devices because of lack of search and limited sorting. ...
This question concerns the description of the SPI communication Electrical Specifications on page 425 of the nRF52840 Product Specification.
The values for "t_spim_vmo...
Hello,
I have a product with QSPI flash that I would like to use nrfjprog to program the flash part. However, the QSPI flash's VCC is controlled (via a FET) from a GPIO...
Summary
With CONFIG_OPENTHREAD_ZEPHYR_BORDER_ROUTER=y and CONFIG_OPENTHREAD_TREL=n , the Zephyr/NCS build fails to link:
ld.bfd: ... openthread_platform.a(trel.c.obj)...
Hello,
I am currently working on a new design based on nRF9151. This design is the evolution of a previous PCB.
The device uses a combined GPS and Cellular antenna, which...
Subject: Support Request for nRF7002 Integration with ThreadX on STM32
Hello Nordic Team,
We are currently using the nRF7002 with our STM32-based device. We have completed...
I am using nrf52832, and I want to use SYSTEM ON Sleep. Also , my wake up sourses are timer based, and also GPIO interrupt based. But I observed that the device cannot go...
