Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi all,
I'm working with nRF52840 PDK and I'm using the last SDK and SoftDevice version: SDK v15.2.0 and SoftDevice v6.1.
I'm using the scanning module introduced in this...
hi
I am using nRF52832.i have added 3 service and and 3 characterastics to one service
1.Peripheral service (accelormeter + gyroscope sensor) and 3 characterstics
2...
Hi, Nordic team. I'm planning to create an iOS 11 BLE app.
I want to create a BLE app that can approximately depict indoor locations after the iOS device scans BLE beacons...
Hello,
I am thinking of using Thingy52 for my project. Before I order Thingy52, I would like to make sure if it will workout for my project.
(1) I wonder if data collected...
I am experimenting with light_switch server example from mesh SDK 2.1.1 . I want to add UART functionality to this example.
I referred to the ble_app_uart example from sdk15...
after cmake -G Ninja ..
-- SDK_ROOT=C:/BLE/SDK/nrf5_SDK_for_Mesh_v2.2.0_src/../nRF5_SDK_15.0.0_a53641a --- set with command line ARG -- PC-Lint executable not found. Linting...
Hi ~ SDK: nrf5_SDK_for_Mesh_v2_0_1 's ligth switch proxy client & proxy server IDEs : SEGGER Embedded Studio for ARM Release 3.40 Build 2018052200.36079 Windows x64 SoftDevices...
I'm looking for the nRF5x SDK v14.2.0-SR3 tha is written on the Smart Remote 3 for nRF52 user's manual. I could not find it on the DevZone, https://developer.nordicsemi.com...
Hi,
I am developing software supporting LEsecure using SDK 12.3 with nRF 51822.
Please tell me what to do when incorrect data is entered in "Passkey entry".
Currently...
Hi.
I've been trying to send a payload with STM32F but I can not. I've used both STM32F103 and STM32F3 to send a payload but neither of them worked. However, when I use...
Hi,
I use nRF5 SDK v15.0.0. In my application I need periodically disable and enable Bluetooth because they are wifi also, which connected to the same antenna. Its mean...
Hi,
I'm trying send me the mac address of the device by UART by the following method:
By serial I receive:
Start b9:24:82:d5:4f:81
The problem its that the device...
Good day
Firstly, an overview.
I am currently busy with a technical proposal for a client. Initial details will result in a completed approx 60 000+ sensor network. My...
Hi EveryBody!
I've begin to work with the n51 family, my board is based on a n51822QFAA H1 IC.
I use Keil5 MDK and a ST-Link V2 programmer. They work fine as I've tested...
IOS, nRF Toolbox 4.4.4, DFU Library version 4.1.1
Attempting to flash to ruuvi with nRF52832 reports
:INFO:Hash failure and
:INFO:Return false in CRC
to J-Link RTT...
