Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
Hi everyone.
I'm trying to transfer new firmware over UART for just only one node in mesh network.
My node will connect to other wireless MCU(ESP32, ESP8266....) over...
I'm using FreeRTOS and trying to get push button events to fire. The events would fire if I held the button down long enough. I found out that the problem was that "FREERTOS...
Hi
I have a custom board implementation that operates as follows:
Monitoring an input pin waiting for low high transition, BLE advertising of device.
When input event...
I'm having trouble having multiple characteristics for my custom service. My main.c looks like this:
Even though I have 2 characteristics added here, I can see just the...
Hi,
I had a few nrf51822s lying around and as I find the chip and the SDK quite convenient to use, I thought about using them in a small MCU project which does not need...
Above you can see the original and commented out modified code for the given example. The modification causes crush to
NRF_BREAKPOINT_COND; // On assert, the system can...
Hi,
I was looking at the Thingy-52-to-nrf52xx demo. I want to capture raw motion data no a DK and save it for further processing. Are there any options (I guess one is nRF91...
hi
i read in earlier questions on the devzone that nordic offers to review the schematic and layout as well as perform tuning free of charge to their customer. Is that still...
Hello every!
I am testing FATFS example with nrf5284 PDK .
CLK - P1.15
MISO - P1.14
MOSI - P1.13
CS - P1.12
My micro sd card module work correctly with STM32 MCU. I...
Hi all,
I am Using SDK15, chipset is nrf52810 , In ble_app_uart application i have added the BLE_NUS_C and TWI application code , before this i have added only TWI to ble_app_uart...
This blog describes how to set up SES (Segger Embedded Studio) for use with nRF SDK:
https://devzone.nordicsemi.com/b/blog/posts/segger-embedded-studio-a-cross-platform...
i'm using DFU for my project, it worked fine until devices has been bonded , DFU cannot work again. i checked and find out that after running interrutps_disable() , the devices...
Hello, I am using an nRF51822 chip, configured to run as a SPI slave. The device receives commands from master, sends commands out of the radio, and relays back RF payloads...
Hello,
I've created my own custom model which allows a client to control the duty cycle of a couple PWM outputs which are on the server. My model is quite simple, it just...
Dear all,
We're started studying payment via BLE with NRF52. But i looking for in Nordic website and google it seem a little subject and document. Can Nordic expert supply...
