Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
Dear All,
while evaluating low-power options in the context of wireless sensors, I've stumbled upon a strange behavior with the nRF52832 using ESB from SDK 14.2. Here's...
Hi
I modified the SPI master example to read an 16-bit ADC at 44.1 kHz.
While the HAL_TIMER achieves its ~22 microseconds quite good, the SPI driver is quite slow: the...
Hi!
I have an observer that listens for advertises from just one ble switch. I can control the leds on the nRF52 DK with the switch. Now i want to connect to nrf connect...
Hey guys,
I have been fighting with this for a couple of days and I am hoping someone can give me some insights as to what might be going on.
We currently use the nRF24L01P...
hi,
i am doing a project where i have to discover custom services on connected ble nodes.
i am using nrf52832 as central device and thingy 52 as peripheral device i have...
Hi Nordic:
I build up an mesh network with following setting:
1. A nRF52 platform with example/light_switch/provisioner with a auto-start-provisioner
2. Another nRF52...
Hi,
I have successfully used the nRF Connect app with a Rigado BMD-350 Dev Board to send a few UART characters back and forth to a new target device using the Rigado BMD...
I started today with the following examples to make a start with serialization:
- ..\examples\connectivity\ble_connectivity\pca10040\ser_s132_hci
- ..\examples\ble_peripheral...
HI:
I am Measuring current on custom hardware with nRF5x DK, Peak current is always too high during testing.Please give me some advice。
I am using the nRF52 DK development...
Hi,
I am working on RTC implementation. I had a doubt.. Is it possible to generate interrupts on different channels (channel 0/1/2/3) using same RTC instance ?
Thanks
Hello,
I'm trying to communicate with another device via I2C. I'm trying to do a simple write but it seems that the TWI NRFX driver is sending wrong data.
I'm just calling...
Hi,
I am implementing a beacon solution and intrested to move from fast to slow and vis versa(slow to fast) advertising modes -
i.e. BLE_ADV_MODE_FAST & BLE_ADV_MODE_SLOW...
Hey,
I have seen some articles which says that voice over BLE (4.0) is possible but there is no standard profile for it.
So far i've seen :
Silicon Labs
STM
T.I...
Hi,
After I reset nrf8001, RDY pin stays hi. I checked the crystal pin, there is no clock. I am using TSX-3225 from Epson with 12pf caps.
Am I suppose to see the clock...
Hi,
I am working on a new project with the secure bootloader (SDK 15) as a part of it. I want to add periodic task that will do several actions for example maintaining the...
