Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hello everyone,
I tested ble_app_beacon example code in SDK15.2 on nrf52810 scanner using nrf connect apple iphone(ios). set APP_COMPANY_IDENTIFIER 0x0059(Nordic id) its...
Does the 2nd argument in the following function SAADC example controls the sampling frequency? If this is not the case then can this saadc example program be modified to be...
If I set CONFIG_SPM=y I can flash merged.hex and successfully call sys_reboot(SYS_REBOOT_COLD) to reboot the system.
If I set CONFIG_SPM=n (and build/flash the SPM project...
I'm using nrf52_SDK_12.2.0, SoftDevice S132 for my application.
I'm implementing SAADC along with UART in my application. I was implementing the SAADC referring to the example...
In regard to the problem described here: https://devzone.nordicsemi.com/f/nordic-q-a/38048/bug-in-how-bootloader-treats-gpregret , it would be interesting for developers,...
When I reset a node after it's provisioned but not configured, the p rovisioner would keep trying to configure it, and would not be able to provision any other nodes.
...
Hello,
I am trying to 'recover nRF52840 dongle after accidental UICR erase' as described here I did modify my dongle as described here
Unfortunately I do not know how...
Hello,
NRF52840
SDK 15.3.0
SoftDevice: s140
OS: Ubuntu
IDE: SES
I am having difficulty getting consistency out of the RTT + NRF_LOG_INFO() print statement. It...
Hello,
I use the nRF5_SDK_for_Thread_and_Zigbee_v3.2.0_9fade31 with nrf52840-DK.
I'm looking for a way to get the transmit state after I sent a udp packet. I would like...
Hi,
we've been trying to reduce power consumption do I able to connect unused pins to GND directly?
Trace 1,2,3,4 do I able to connect to the GND?
Thanks, in advance...
Hi,
I am the first time programming with nordic and Segger. As I received the Thingy91 I just the getting started assistent to set up the toolchain.
This worked fine so...
I have the following setup, master (Nrf24L01) and several clients (Nrf52840), the clients listen, the master sends a message to one client and switches to listen. When the...
While most of nRF5 DSK modules have conditional compiling, such as
#if NRF_MODULE_ENABLED(BLE_DIS) the components/ble/ble_services/ble_dfu/*.c lack these macros. In my project...
