Hi there is a problem in github.com/.../nrf51-UART-examples
any one can help?
I put empty loop in main, and comment off all ble related int. and I process uart_evt by...
Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hello,
In our application we heavily use the application scheduler. This was done for 2 main reasons:
serialize access to system resources
enable the soft device to...
Good Afternoon,
I'm writing some config data on an empty record the first time I turn on my board and updating that same record every next time I turn on the board.
...
Hi everybody I have a couple of questions regarding power consumption for the nRF 52 DK Rev. 1 (nRF52832). I currently have an application where I sample 12-bit ADC data via...
I'm working on support for several custom characteristics that require long write support. I'm using the nrf_ble_qwr library, and I've noticed what seems to be a discrepancy...
Hello,
I have an nRF52 DK here that behaves strangely since a few days. Hardware id is 0xc7
When I boot it up with my firmware, sd_ble_enable takes around 2 seconds...
Hi
We have used DTM functionality in nRFgo Studio to carry out signal strength testing during the design stage. We now want to automated this testing in end-of-line testing...
Hello,
I beginner for Nordic board, developing small device using BLE.
I build softdevice, bootloader and application. I checked working DFU mode(via serial, not BLE...
What a software i can use for develloping a Bluetooth Profil Mesh (BLE5) ? Hello every body , i want to develop a bluetooth mesh profil and i don't known which a IDE i will...
Hi,
I make my first project with the nRF52832.
On my first pcb the bluetooth works fine, but this pcb was not fully assembled.
Now i have made a second pcb that is fully...
I need to create and update some data record, the record contains some data that will be updated sequentially or randomly. But the sdk does not execute fds_gc automatically...
I am reading through IETF RFC7668, IPv6 over BLUETOOTH(R) Low Energy . In section 3.2.2, it states the following:
At network interface initialization, both 6LN and 6LBR...
hi
I am really confused For Indoor Asset Tracking which is better Nordic Mesh SDK or Thread
I see Thread Supports Cloud connectivity.
Can the device based on nRF52840...
Hi @ll,
I'm still trying to get the Mesh DFU example up and running. I'm following the guide in the documentation. (Mesh Version 2.0.0: it's the same in 2.0.1 so don't worry...
Hello all!
I am working in a project in which I have designed my own PCB using the nRF51822 chip because is gonna be used for BLE applications.
I have some experience...
