When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Currently i am testing the nRF52840 Preview DK DFU function. Is the NRF52840 support by SoftDevice(S132)? and also match with the SDK(nRF5_SDK_v13.x.x) ?
thanks!
Hi,
is it possible to get some statistical information about a BLE connection?
Background is, that I'm experiencing connection problems (degrading throughput, stuttering...
I am using the Mesh-SDK v1.0.0, the device is the nRF52832xxAA on PCA10040-Boards with the Softdevice s132. I am new to the development with BLE, and specially mesh.
I have...
Hi
I would like to modulate the positive output of the UART using PWM
I know i can feed the UART and a PWM putput into a AND gate no problem, but im wondering if there...
Is there a ready example to run nRf51822 as a controller to external host via HCI commands over UART or USB?
e.g. I want to interface the Nordic chip with an open source...
I am using softDevice S140 with SDK 14.2.0_17b948a, working with the ble_app_blinky.
I need to be able to connect one peripheral device to multiple central devices (peripheral...
I connected via a USB cable my ppk to my computer. But when I fire up ppk.py, it says "no response from ppk. Check power, debugger connection and make sure the firmware is...
Is there any other way of programming the Nordic Thingy other than using the nrf52 DK? Where to get the programming/debugging port's pinout , I didn't find that in the hardware...
After connect devices status GAP Secure status ...->evt.gap_evt.params.auth_status.auth_status 0x0D In documentation absend this code = 0x0D What is It?
I would like to use 1.3 V System power to supply some external circuit that may need max 10 mA. This voltage is available via pin DEC4.
I expect that you are going to...
Hi There, I'm very new to mesh and have a bit of a learning curve to understand the mesh SDK. A few questions for those in the know....
I have been playing around with the...
hi,
can anyone share sample code for getting accel values from MPU9255.?
I have tried with this ,Iam not getting output.
Chip :nrf52382
Board : nrf52Dk - PCA10040...
Hi
How can i configure NRF_LOG with IAR and J-Link connected via USB to a RAK 813 BreakBoard, i'm testing BLE SCAN Application.
Regards,
Julio César Morales bErmúde
Is there a way to modify the code in the ios nrf beacon app to identify nordic beacons?
I am aware that the manufacturing id must be set to 0x004C in order to be identified...
