I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
In the example / serial in SES I see the softdevice is loaded as an "additional load file"
$(SDK_ROOT:../../../nRF5_SDK_16.0.0_98a08e2)/components/softdevice/s140/hex/s140_nrf52_7...
I am quite new to the nrf9160. Trying to run the gps example https://github.com/ExploratoryEngineering/nrf9160-gps . But everytime I get an error Failed to start GPS. I am...
Hello, the SDK example ble_peripheral\ble_app_uart includes the code below in order to forward data from the UART over the BLE. What it does is wait for a CRLF, or a certain...
hello
i have created 1 custom service for that created 3 characteristics.
with that 3 characteristics i'm trying to notify by using nrf connect app.
my question is...
We are looking for a BLE-enabled chip which can bind to a smartphone, with the aim of performing proximity tests. to make sure the person in possession of the chip is indeed...
We want to design a small tracker for key rings like car keys etc, it will be linked with mobile app. Is it possible to do so?
Whatever I have read till now is it is possible...
Hi,
We are planning to run the nRF52840 in CKAA configuration 3 (attached) in Normal Mode. When we boot, our regulator will provide VDD = VDDH = 1.8V. Reading through the...
Our product is using NRF24L01+ and PA to transmitter data. It pass all the test of FCC PART C but the BAND Edge measurement.
The below 2 pictures is NRF24L01+ Band edge...
Hello everyone,
I have been dealing with this issue for some time now, and I think it's time to find a definitive solution, I am sure there is one!
For my projects,...
I had some questions when using nRF5SDK160098a08e2\examples\dfu\secure_bootloader\pca10056_s140_ble for OTA test. Who can help me answer my question?
1. Can I return the...
Hi,
i have created some custom characteristics and i am enabling read and write characteristics in that, but when i am trying to write or read some data it seems that it...
Hi everyone,
I am trying to connect my nRF 9160 DK and Thingy:91 to TIM (Telecom Italia Mobile) CAT-NB1 network provider from Brazil. I am using the Asset Tracker and...
Hello,
For my project I want to use broadcast packages to send data to multiple devices at the same time.
I've seen that there is a beacon application that "should"...
Hi,
I'm trying to develop a custom service and am following a few examples in trying to do so. The software crashes for me everytime after advertising the new service...
I am building a custom device that incorporates the nRF9160. For testing I would like the device to work in China. I believe NB-IoT is the only network that is supported by...
