Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hi,
I am working with a custom board with a third party NRF52832 module. On my board I have a DS3231M real time clock IC communicating with the NRF52832 via I2C/TWI and...
I am trying to have a bluetooth bond between the device and the app,
how to set a security key to bond it with the android app? and also can I know how to encrypt all the...
Hi,
I have a question about getting the appkey from flash:
I am using the device state manager for key management. I do a ramdom generation of netkey and appkey on first...
I have a few different Fanstel Eval boards that contain the nRF52840 SoC - starting with the BT840XE. I'm able to flash the board with example firmware and my own custom firmware...
Been working on an unsoldered, untinkered, and in all ways untainted nRF5340-PDK. No jumpers changes. No solderbridges cut. All working fine, but all of the sudden I cannot...
Hi! I want to program a custom BLE application (as Central/master/GATT client device) to run on a Windows PC using a nRF51 Dongle (PCA10031 board) attached through USB in...
Hi,
I am working on the software development of a product based on an nRF52832.
We began our development on the nrf52810 and then moved on to the nRF52832 as it became...
Hello,
I'm struggling to connect to an MQTT-SN Gateway when the device is configured for low power. Currently using MAC-OS Catalina 10.15.3, SES version 4.42 and have tried...
I tried to install the nRF Connect SDK v1.3.0-rc1 error
I open git-bash.exe to execute the ncsmgr init-ncs command, the following error occurred during the installation...
nRF Connect SDK v1.3.0 using nRF Connect v3.4.2 - ToolChain Manager
I am trying to install nRF Connect SDK v1.3.0 using nRF Connect v3.4.2 - ToolChain Manager using nRF...
I am writing a code to blink the LEDS , the 3rd one is not turning off.
Here is the code-
#include <stdbool.h> #include <stdint.h> #include "nrf_delay.h" #include "boards...
Hi,
My device is using nRF52840 with s140 of SDK v16. BLE feature is used with SD .
Sometimes application hard faults in SD are observed in devices deployed. It is quite...
Hello,
I find that after I DFU a new application (using the nRF Connect Mobile App), my device boots into that new application and reconnects to the App, as expected. Then...
Hi,
I am using nRF51822-CEAA with S110 SoftDevice on a custom board which is commercially deployed now. I am using IAR 7.80.2 and Segger JLink Ultra+. I found there are...
