Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I have a Unix time stamp value stored on the Nordic board that comes from a GATT connection.
I am using SDK 15 s140 pca10056 NRF52840-dk.
I need to update this value...
I am using nrf52840 dk for zigbee project with two xbee modules. One xbee is configured as coordinator and other as end device and nrf board is supposed to act as router....
I use nRF52810 + 15.3.0 s112 to develop. After the equipment upgrade is successful, I power up the equipment again, and the equipment is always in DFU mode.
For some reason it seems that the TWI master does not generate a NACK. As a consequence, the TWI slave keeps sending data. I have managed to create a very simple function...
Hi
I have a really strange issue with an NRF52840. I'm using it with an MPU-9250 connected via TWI. I've modifed the excellent library:
https://github.com/Martinsbl/nrf5...
I want to use RTC handler , so I used NRF_DRV_RTC_INSTANCE.
I use SDK 16.0.
" 'NRFX_RTC"_INST_IDX' undeclared here (not in a function) ; did you mean 'NRFX_RTC_INT_TICK...
I've been reading into the "nRF5 SDK for Thread and Zigbee v4.0.0", and I wondered about the limitations , in specific
is that a hardcoded limitation, or does it require...
Hi I programmed the nRF mesh experimental dimming example on the nRF52832 chip. I noticed that, when using Bluetooth Mesh provisioning apps (I've tried several to verify this...
I am trying to setup a PPI channel to trigger the SAADC in simple mode. However, it appears as though the SAADC module is disabled after every read. I.e. if I write:
...
I am unable to flash the DK board facing issue " Failed to Connect to Target. No idcode detected. Please check connections and Target interface Type."
DK Board Details:...
I am using LSM9DS1 IMU, nRF52840 with SDK v16.0.0. I configured the IMU to raise an interrupt when the FIFO buffer be full by writing to register INT2_CTRL the value '0b00011000...
I can't see it!
https://www.nordicsemi.com/Software-and-Tools/Development-Tools/nRF-Connect-for-desktop
The 'Downloads' section contains only the "host" native app - doesn...
I am trying to interface the BMM150 magnetometer with the nRF58240 MICRCONTROLLER, Iam able to establish the I2C connection and get the return value from the reg 0x40 and...
The stock LPN client for Mesh SDK v4.0.0 throws NRF_MESH_EVT_SAR_FAILED when replying to a publication set message via a friend node.
All code, reproduction data and log...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
1) I want to write Serial number into...
